Related Experiment Video

Updated: Nov 22, 2025

Tracking Infiltration Front Depth Using Time-lapse Multi-offset Gathers Collected with Array Antenna Ground Penetrating Radar
07:14

Tracking Infiltration Front Depth Using Time-lapse Multi-offset Gathers Collected with Array Antenna Ground Penetrating Radar

Published on: May 1, 2018

8.0K

X-Band Radar Cross-Section of Tandem Helicopter Based on Dynamic Analysis Approach

Zeyang Zhou1, Jun Huang1

  • 1School of Aeronautic Science and Engineering, Beihang University, Beijing 100191, China.

Sensors (Basel, Switzerland)
|January 6, 2021
PubMed

Keywords:
a double main rotorelectromagnetic scattering characteristicshelicoptertandem layout

More Related Videos

Evaluation of an Exclusive Spur Dike U-Turn Design with Radar-Collected Data and Simulation11:41

Evaluation of an Exclusive Spur Dike U-Turn Design with Radar-Collected Data and Simulation

Published on: February 1, 2020

20.7K
Experimental Investigation of the Flow Structure over a Delta Wing Via Flow Visualization Methods09:17

Experimental Investigation of the Flow Structure over a Delta Wing Via Flow Visualization Methods

Published on: April 23, 2018

11.0K

Related Concept Videos

Method of Sections: Problem Solving I01:27

Method of Sections: Problem Solving I

Consider a symmetrical roof truss structure, composed of vertical, diagonal, and horizontal members. The length of each horizontal member is 4 m. The lengths of the vertical members FB and HD are 4 m, while the length of member GC is 6 m. The loads acting at joints F, G, and H are 2 kN, while those at joints A and E are 1 kN.
885
Moments of Inertia: Problem Solving01:14

Moments of Inertia: Problem Solving

The second moment of an area, also known as the moment of inertia of an area, is a geometric property of a shape that reflects its resistance to change. The moment of inertia of an area can be calculated for both two-dimensional and three-dimensional shapes. The moment of inertia of an area is calculated by taking the sum of the product of the area and the square of its distance from a chosen axis of rotation. For two-dimensional shapes, the moment of inertia can be expressed as a single...
863
Relative Motion Analysis using Rotating Axes-Problem Solving01:29

Relative Motion Analysis using Rotating Axes-Problem Solving

Consider a crane whose telescopic boom rotates with an angular velocity of 0.04 rad/s and angular acceleration of 0.02 rad/s2. Along with the rotation, the boom also extends linearly with a uniform speed of 5 m/s. The extension of the boom is measured at point D, which is measured with respect to the fixed point C on the other end of the boom. For the given instant, the distance between points C and D is 60 meters.
Here, in order to determine the magnitude of velocity and acceleration for point...
548
Shear on the Horizontal Face of a Beam Element01:16

Shear on the Horizontal Face of a Beam Element

To understand shear on the flat side of a prismatic beam element, consider the vertical and horizontal shearing forces, and the normal forces, acting on the element. The element's upper (U) and lower (L) sections, which are divided by the beam's neutral axis, are examined. The equilibrium of these forces is determined by applying the equilibrium equation, which helps identify the horizontal shearing force. This force is directly related to the bending moments and the cross-section's...
399
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
384
Shear and Bending Moment Diagram: Problem Solving01:24

Shear and Bending Moment Diagram: Problem Solving

When analyzing a beam supporting concentrated loads and a distributed load, drawing the shear and bending moment diagrams is essential. These diagrams help understand the internal forces and moments acting on the beam, which is crucial for designing safe and efficient structures. Follow these steps to create the shear and bending moment diagrams:
Draw a Free-Body Diagram: Start by drawing a free-body diagram of the entire beam, including the concentrated loads, distributed load, and reaction...
2.6K