Related Experiment Video

Updated: Nov 12, 2025

Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements
09:36

Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements

Published on: June 25, 2021

3.3K

Clock conversion for burst-mode digital coherent QPSK receivers in a PON upstream transmission with a 100-ppm clock

Noriko Iiyama, Masamichi Fujiwara, Takuya Kanai

    Optics Express
    |March 17, 2021
    PubMed

    More Related Videos

    A Photonic System for Generating Unconditional Polarization-Entangled Photons Based on Multiple Quantum Interference07:56

    A Photonic System for Generating Unconditional Polarization-Entangled Photons Based on Multiple Quantum Interference

    Published on: September 5, 2019

    8.8K
    Quasi-light Storage for Optical Data Packets07:45

    Quasi-light Storage for Optical Data Packets

    Published on: February 6, 2014

    11.1K

    Related Concept Videos

    Time and frequency -Domain Interpretation of Phase-lag Control01:21

    Time and frequency -Domain Interpretation of Phase-lag Control

    Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
    Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any...
    185
    Time and frequency -Domain Interpretation of Phase-lead Control01:24

    Time and frequency -Domain Interpretation of Phase-lead Control

    Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
    The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
    205
    Upsampling01:22

    Upsampling

    Managing signal sampling rates is essential in digital signal processing to maintain signal integrity. A decimated signal, characterized by a reduced frequency range due to its lower sampling rate, can be upsampled by inserting zeros between each sample. This upsampling process expands the original spectrum and introduces repeated spectral replicas at intervals dictated by the new Nyquist frequency. To refine this zero-inserted sequence, it is passed through a lowpass filter with a cutoff...
    433
    Cut-off Frequency of BJT01:17

    Cut-off Frequency of BJT

    Cut-off frequencies in Bipolar Junction Transistors (BJTs) mark the transition between the signal's pass band and stop band, influencing their performance in amplifying or attenuating frequencies. These frequencies are crucial for designing BJTs to meet specific operational requirements in electronic circuits.
    Alpha Cut-Off Frequency: Pertinent to the common-base configuration, the alpha cut-off frequency defines the upper-frequency limit at which the current gain, alpha, remains stable. As...
    1.1K
    Time and frequency -Domain Interpretation of PI Control01:27

    Time and frequency -Domain Interpretation of PI Control

    Proportional-Integral (PI) controllers are essential in many control systems to improve stability and performance. They are commonly used in everyday devices like thermostats to enhance system damping and reduce steady-state error. When the zero in the controller's transfer function is optimally placed, the system benefits significantly in terms of stability and accuracy.
    Acting as a low-pass filter, the PI controller slows the system's response and extends settling times. This requires...
    267
    NMR Spectrometers: Radiofrequency Pulses and Pulse Sequences01:17

    NMR Spectrometers: Radiofrequency Pulses and Pulse Sequences

    A pulse is a short burst of radio waves distributed over a range of frequencies that simultaneously excites all the nuclei in the sample. Upon passing a radio frequency pulse along the x-axis, the nuclei absorb energy corresponding to their Larmor frequencies and achieve resonance. This shifts the net magnetization vector from the z-axis toward the transverse plane. This angle of rotation of the magnetization vector, or the flip angle, is proportional to the duration and intensity of the pulse.
    1.2K