Related Experiment Video

Updated: Oct 17, 2025

The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry
12:14

The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry

Published on: August 12, 2013

22.0K

Fundamental-ray aberration analysis of off-axial optical systems: analytical formulae of first-order aberrations

Kentaro Mori, Yoshio Hayasaki, Keisuke Araki

    Applied Optics
    |October 8, 2021
    PubMed

    More Related Videos

    Comparison of Agreement and Accuracy using Binocular Wavefront Optometer with Autorefractor and Phoropter05:14

    Comparison of Agreement and Accuracy using Binocular Wavefront Optometer with Autorefractor and Phoropter

    Published on: September 16, 2025

    168
    High-speed Continuous-wave Stimulated Brillouin Scattering Spectrometer for Material Analysis07:55

    High-speed Continuous-wave Stimulated Brillouin Scattering Spectrometer for Material Analysis

    Published on: September 22, 2017

    10.3K

    Related Concept Videos

    Beams with Unsymmetric Loadings01:17

    Beams with Unsymmetric Loadings

    Analyzing a supported beam under unsymmetrical loadings is essential in structural engineering to understand how beams respond to varied force distributions. This analysis involves calculating the deflection and identifying points where the slope of the beam is zero, which are crucial for ensuring structural stability and functionality.
    The first moment-area theorem determines the slope at any point on the beam. This theorem indicates that the change in slope between two points on a beam...
    199
    Focusing of Light in the Eye01:16

    Focusing of Light in the Eye

    Light rays enter the eye through the cornea, a transparent dome-shaped tissue that is the eye's outermost layer. The cornea bends or refracts, light rays traveling to the pupil. The shape of the cornea determines how much of the light is bent and whether the image will be focused correctly on the retina at the back of the eye. Once the light has passed through both refraction layers, it converges into a single focal point onto a small area. This is where photoreceptors start transforming...
    3.5K
    Equation of the Elastic Curve01:23

    Equation of the Elastic Curve

    The concept of curvature in plane curves, crucial in structural engineering, defines how sharply a beam bends under load. This curvature is determined using the curve's first and second derivatives.
    Consider a cantilever beam with a point load at its free end (for instance, a diving board). When analyzing beam deflection with small slopes, the shape of the beam's elastic curve becomes key. The governing equation for this analysis involves the bending moment and the beam's flexural...
    729
    Circular Shaft - Stresses in Linear Range01:13

    Circular Shaft - Stresses in Linear Range

    Consider a scenario where a circular shaft is subject to torque that remains within the boundaries of Hooke's Law, avoiding any permanent deformation. So, the formula for shearing strain is revisited. This formula is multiplied by the modulus of rigidity, and then Hooke's Law for the shearing stress and strain is applied. As a result, the equation for shearing stress in a shaft can be derived.
    412
    Deformation in a Circular Shaft01:10

    Deformation in a Circular Shaft

    One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
    502
    Stress Concentrations in Circular Shafts01:18

    Stress Concentrations in Circular Shafts

    Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
    295