Related Experiment Video

Updated: Oct 11, 2025

Implementation of a Hyperbolic Vortex Plasma Reactor for the Removal of Micropollutants in Water
06:35

Implementation of a Hyperbolic Vortex Plasma Reactor for the Removal of Micropollutants in Water

Published on: July 25, 2025

392

Design and development of a rapid, high voltage capacitor charging power supply based on third order resonant

Reghu Thekkeppat1, Sonu K Singh2, Mahendra Lad1

  • 1Radio Frequency Systems Division, Raja Ramanna Centre for Advanced Technology, Indore, M.P. 452013, India.

The Review of Scientific Instruments
|December 2, 2021
PubMed

More Related Videos

Rapid Scan Electron Paramagnetic Resonance Opens New Avenues for Imaging Physiologically Important Parameters In Vivo08:01

Rapid Scan Electron Paramagnetic Resonance Opens New Avenues for Imaging Physiologically Important Parameters In Vivo

Published on: September 26, 2016

9.5K
Fabrication and Characterization of Superconducting Resonators10:26

Fabrication and Characterization of Superconducting Resonators

Published on: May 21, 2016

11.5K

Related Concept Videos

Design Example: Underdamped Parallel RLC Circuit01:17

Design Example: Underdamped Parallel RLC Circuit

Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
Starting with a fixed...
417
RC Circuit with Source01:15

RC Circuit with Source

When a DC source is abruptly applied to an RC (Resistor-Capacitor) circuit, the voltage can be represented as a unit step function. The voltage across the capacitor, known as the step response, characterizes how the circuit reacts to this sudden change in input.
Due to the inherent properties of a capacitor, its voltage cannot change instantaneously. This means that immediately after the switch is closed, the capacitor's voltage remains the same as it was just before the switch was closed.
1.8K
Design Example: Capacitance Multiplier Circuit01:20

Design Example: Capacitance Multiplier Circuit

In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
1.0K
RC Circuits: Charging A Capacitor01:30

RC Circuits: Charging A Capacitor

A circuit containing resistance and capacitance is called an RC circuit. A capacitor is an electrical component that stores electric charge by storing energy in an electric field. Consider a simple RC circuit having a DC (direct current) voltage source ε, a resistor R, a capacitor C, and a two-way position switch. In the circuit, the capacitor can be charged or discharged depending on the position of the switch.
When the switch is moved to connect the battery, the circuit reduces to a simple...
4.0K
Voltage Doubler Circuit01:23

Voltage Doubler Circuit

A voltage doubler circuit integrates two main components: a clamping section and a rectifier section. The clamping section consists of a capacitor (C1) and a diode (D1), whereas the rectifier section is equipped with another diode (D2) and capacitor (C2). This circuit produces an output voltage with twice the amplitude of the sinusoidal input voltage.
964
Second-Order Circuits01:17

Second-Order Circuits

Integrating two fundamental energy storage elements in electrical circuits results in second-order circuits, encompassing RLC circuits and circuits with dual capacitors or inductors (RC and RL circuits). Second-order circuits are identified by second-order differential equations that link input and output signals.
Input signals typically originate from voltage or current sources, with the output often representing voltage across the capacitor and/or current through the inductor. For example, in...
1.7K