Related Experiment Video

Updated: Oct 7, 2025

Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements
09:36

Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements

Published on: June 25, 2021

3.2K

3-D twelve-port multi-service diversity antenna for automotive communications

Lekha Kannappan1, Sandeep Kumar Palaniswamy2, Malathi Kanagasabai3

  • 1Department of Electronics and Communication Engineering, SRM Institute of Science and Technology, Kattankulathur, 603203, India.

Scientific Reports
|January 11, 2022
PubMed

More Related Videos

Calibration of Vector Network Analyzer for Measurements in Radio Frequency Propagation Channels10:00

Calibration of Vector Network Analyzer for Measurements in Radio Frequency Propagation Channels

Published on: June 2, 2020

21.6K
Effective Analysis of Human Exposure Conditions with Body-worn Dosimeters in the 2.4 GHz Band06:43

Effective Analysis of Human Exposure Conditions with Body-worn Dosimeters in the 2.4 GHz Band

Published on: May 2, 2018

7.1K

Related Concept Videos

Diversity of Antigen Receptors01:28

Diversity of Antigen Receptors

Antigen receptors are essential components of the immune system crucial in defending the body against foreign invaders. These receptors are present on the surface of B and T cells, enabling them to recognize antigens and mount an appropriate immune response.
Before encountering any antigen, lymphocytes express these receptors. On B cells, the antigen receptor is a membrane-bound antibody molecule called BCR; on T cells, it is a T cell receptor or TCR. B and T cell receptors are composed of two...
889
Bus Impedance Matrix01:24

Bus Impedance Matrix

Calculating subtransient fault currents for three-phase faults in an N-bus power system involves using the positive-sequence network. When a three-phase short circuit occurs at a specific bus, the analysis uses the superposition method to evaluate two separate circuits.
In the first circuit, all machine voltage sources are short-circuited, leaving only the prefault voltage source at the fault location. The positive-sequence bus impedance matrix can be determined by solving the nodal equations,...
196
Design Example01:23

Design Example

The innovation of touch-tone telephony revolutionized the telecommunications industry by replacing the traditional rotary dial with a dual-tone multi-frequency (DTMF) signaling system. This system uses a matrix-style keypad with buttons arranged in four rows and three columns, creating 12 distinct signals each assigned to a pair of frequencies. Each button press results in a simultaneous generation of two sinusoidal tones – one from a low-frequency group (697 to 941 Hz) and one from a...
396
Design Example: Automobile Ignition System01:14

Design Example: Automobile Ignition System

The automobile's ignition system plays a vital role by ensuring the timely ignition of the fuel-air mixture in each cylinder. This ignition is facilitated by a spark plug, which is composed of two electrodes separated by an air gap. A spark forms across this air gap when a substantial voltage is generated between the electrodes, leading to the ignition of the fuel.
One can generate a large voltage using a car battery of 12 volts with the help of inductors. Inductors are known for opposing...
373
The Antenna Complex01:15

The Antenna Complex

Plants and other photosynthetic organisms comprise pigments capable of absorption of direct sunlight. These pigments are present in the reaction center - the main site of photochemical reactions as well as in the antenna complex. Under average light conditions, the rate at which reaction center pigments absorb light is far below the electron transport chain's capacity. As a result, the reaction center alone cannot provide enough energy to drive photosynthesis. The photosynthetic efficiency can...
6.4K
Pilot and Numeric Relaying01:21

Pilot and Numeric Relaying

Pilot relaying is a type of differential protection used in power systems. It compares electrical quantities at the terminals of equipment via a communication channel instead of direct relay interconnection. This method is essential for transmission lines where the terminals are far apart, typically up to 80 km for lines with 69 to 115 kV ratings. Four types of communication channels are used for pilot relaying:
156