Related Experiment Video

Updated: Oct 3, 2025

Four-Dimensional CT Analysis Using Sequential 3D-3D Registration
05:05

Four-Dimensional CT Analysis Using Sequential 3D-3D Registration

Published on: November 23, 2019

8.1K

The dynamic rotation axis of ulnohumeral joint during active flexion-extension: an in vivo 4-dimensional computed

Hua Liu1, Erica Kholinne2, Yucheng Sun1

  • 1Department of Hand Surgery, Hand Surgery Research Center, Affiliated Hospital of Nantong University, College of Medicine, University of Nantong, 20 West Temple Road, Nantong, 226001, Jiangsu, China.

BMC Musculoskeletal Disorders
|February 17, 2022
PubMed
Abstract

Keywords:
Collateral ligament reconstructionElbow jointFour-dimensional computed tomographyInstantaneous rotation axis

More Related Videos

In Vivo Quantification of Hip Arthrokinematics during Dynamic Weight-bearing Activities using Dual Fluoroscopy07:43

In Vivo Quantification of Hip Arthrokinematics during Dynamic Weight-bearing Activities using Dual Fluoroscopy

Published on: July 2, 2021

3.2K
Measuring 3D In-vivo Shoulder Kinematics using Biplanar Videoradiography06:09

Measuring 3D In-vivo Shoulder Kinematics using Biplanar Videoradiography

Published on: March 12, 2021

3.3K

Related Concept Videos

Bones of the Upper Limb: Ulna01:15

Bones of the Upper Limb: Ulna

The ulna and radius are parallel bones of the antebrachium or the forearm. The ulna lies medially and consists of a bony tip called the olecranon process at its proximal end. This hook-like projection articulates with the olecranon fossa of the humerus and forms the "hinged" ulnohumeral part of the elbow joint. This joint facilitates forearm extension and flexion while preventing its hyperextension. Similarly, the coronoid process, another bony projection on the proximal/anterior side...
3.0K
Bones of the Upper Limb: Humerus01:19

Bones of the Upper Limb: Humerus

The upper limb consists of the arm, forearm, wrist, and hand bones. The humerus is the single bone of the upper arm region. Proximally, it has a large, spherical, smooth head that articulates with the glenoid cavity of the scapula to form the glenohumeral or shoulder joint. The margin of the head is the anatomical neck, a residual epiphyseal plate. Laterally it extends to form bony projections called the greater tubercle and the lesser tubercle. Next to the tubercles is the surgical neck, a...
5.2K
Computed Tomography01:10

Computed Tomography

Tomography refers to imaging by sections. Computed tomography (CT) is a non-invasive imaging technique that uses computers to analyze several cross-sectional X-rays to reveal minute details about structures in the body.
The technique was invented in the 1970s and is based on the principle that as X-rays pass through the body, they are absorbed or reflected at different levels. In the technique, a patient lies on a motorized platform while a computerized axial tomography (CAT) scanner rotates...
6.8K
Functional Classification of Joints01:09

Functional Classification of Joints

Functional Classification of Joints
The functional classification of joints is determined by the amount of mobility between the adjacent bones. Joints are functionally classified as a synarthrosis or immobile joint, an amphiarthrosis or slightly moveable joint, or as a diarthrosis, a freely moveable joint. Fibrous and cartilaginous joints can be functionally classified as either synarthroses  or amphiarthroses, whereas all synovial joints are classified as diarthroses.
Synarthrosis
An...
5.2K
Eccentric Axial Loading in a Plane of Symmetry01:16

Eccentric Axial Loading in a Plane of Symmetry

Eccentric axial loading occurs when an axial load is applied away from the centroidal axis of a structural member. This scenario is common in engineering, where structural elements may not be directly aligned due to various design or functional requirements.
320
Rotational Motion about a Fixed Axis01:26

Rotational Motion about a Fixed Axis

A rigid body's rotation around a fixed axis makes every point within it trace a circular path around a specific line or point. The term given to this type of spinning is defined by the angular position, symbolized by the angle θ. This angle is gauged from a static reference line to the revolving object. From this angular position, any variation is referred to as angular displacement, denoted by dθ. The extent of this displacement can be calculated in degrees, radians, or...
788