Related Experiment Video

Updated: Sep 30, 2025

Fabrication and Testing of Catalytic Aerogels Prepared Via Rapid Supercritical Extraction
09:28

Fabrication and Testing of Catalytic Aerogels Prepared Via Rapid Supercritical Extraction

Published on: August 31, 2018

7.4K

Study on a Fault Mitigation Scheme for Rub-Impact of an Aero-Engine Based on NiTi Wires

Qiang Pan1, Tian He1, Wendong Liu2

  • 1School of Transportation Science and Engineering, Beihang University, Beijing 100191, China.

Sensors (Basel, Switzerland)
|March 10, 2022
PubMed

Keywords:
aero-enginefault mitigationrub-impactshape memory alloytip clearance

More Related Videos

A Rapid Method for Modeling a Variable Cycle Engine04:58

A Rapid Method for Modeling a Variable Cycle Engine

Published on: August 13, 2019

7.7K
Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator06:45

Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator

Published on: October 28, 2022

1.8K

Related Concept Videos

Internal Combustion Engine01:20

Internal Combustion Engine

The internal combustion engine is a heat engine that uses the byproducts of combustion as the working fluid instead of using a heat transfer medium to transfer heat. The combustion is done in a way that produces high-pressure combustion products that can be expanded through a turbine or piston to create work. Internal combustion engines can again be categorized into three kinds: (1) spark ignition gasoline engines, most commonly used in automobiles, (2) compression ignition diesel engines that...
1.9K
Net Torque Calculations01:19

Net Torque Calculations

When a mechanic tries to remove a hex nut with a wrench, it is easier if the force is applied at the farthest end of the wrench handle. The lever arm is the distance from the pivot point (the hex nut in this case) to the person’s hand. If this distance is large, the torque is higher. Only the component of the force perpendicular to the lever arm contributes to the torque. Therefore, pushing the wrench perpendicular to the lever arm is more advantageous. If multiple people apply force to...
9.7K
Node Analysis for AC Circuits01:14

Node Analysis for AC Circuits

Consider an angioplasty system featuring a catheter equipped with a turbine, a critical tool for removing plaque deposits from coronary arteries. This intricate medical device operates using a circuit model reminiscent of a dual-node RLC circuit powered by a current-controlled voltage source.
To unravel the complexities of this system, nodal analysis is employed, a powerful technique founded on Kirchhoff's current law (KCL), which remains valid for phasors. AC circuits can effectively be...
388
Line Protection with Impedance Relays01:27

Line Protection with Impedance Relays

Coordinating time-delay overcurrent relays in complex radial systems and directional overcurrent relays in multi-source transmission loops can be challenging. Impedance relays address these issues by responding to the voltage-to-current ratio, specifically measuring the apparent impedance of a line. These relays become more sensitive during faults as current increases and voltage decreases, thereby reducing the apparent impedance.
Under normal conditions, low load currents keep the measured...
142
Design of Transmission Shafts01:16

Design of Transmission Shafts

The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by...
501
Rolling Resistance: Problem Solving01:17

Rolling Resistance: Problem Solving

Rolling resistance, also known as rolling friction, is the force that resists the motion of a rolling object, such as a wheel, tire, or ball, when it moves over a surface. It is caused by the deformation of the object and the surface in contact with each other, as well as other factors like internal friction, hysteresis, and energy losses within the materials. Rolling resistance opposes the object's motion, requiring additional energy to overcome it and maintain movement. In practical...
483