Related Experiment Video

Updated: Sep 24, 2025

Measuring 3D In-vivo Shoulder Kinematics using Biplanar Videoradiography

Measuring 3D In-vivo Shoulder Kinematics using Biplanar Videoradiography

Published on: March 12, 2021

3D orientation and kinematic characteristics of zygapophyseal joints while sitting

Bowen Kou^1,2, Yang Song^2,3, Ye Han²

¹Department of Spine Surgery, Tianjin Hospital of Tianjin University, Tianjin, China.

Annals of Translational Medicine

|May 9, 2022

Abstract

Background:

Orientation of the lumbar facet joints (FJs) in the transverse plane is associated with degenerative lumbar spine disease. However, there is a lack of measurements of the sagittal and coronal facet angles, and the effect of 3D facet angles on joint motion in the sitting position is unknown. The present study was to investigate the 3D orientation and in vivo motion characteristics of the FJ in the sitting position.

Methods:

Dual fluoroscopic imaging system and computed tomography (CT) were used to determine the 3D orientation and kinematic characteristics of FJs. L3-S1 segments were studied in 10 asymptomatic participants (5 male and 5 female, age: 25-35 years, body mass index: 22.4±1.8). Angles of the facet in the sagittal, coronal, and axial planes, and the range of motion of the FJs in seated flexion and extension movements were measured.

Results:

The difference in sagittal facet angles between the 2 sides of the L3-S1 facet joints was not significant. The superior coronal facet angle on the left side of L5 was significantly smaller than that on the right side by 6.4° (P=0.01). The inferior transverse facet angle on the left side of L5 was greater than that on the right side by 7.1; the results were not statistically significantly different. In the sitting position, the range of motion of the left and right sides of L5-S1 differed significantly, with the right side being 5.5° (P=0.004) and 11.7° (P=0.026) greater than the left side in the sagittal and coronal planes, respectively. There was a correlation between mobility and the 3D orientation angle of the FJs in each segment.

Conclusions:

Quantification of the 3D orientation of the lumbar spine FJs provides new perspectives to study the kinematics of the lumbar spine and the etiology of lumbar degenerative diseases. In sitting flexion and extension movements, there is a significant difference in the left-right lateral mobility of the FJs of the L5-S1 segments. With the exception of the transverse facet angle of the lumbar spine FJs, the sagittal and coronal facet angles also have an effect on lumbar spine mobility.

Keywords:

3D orientation Zygapophyseal joint facet tropism (FT)sitting

More Related Videos

In Vivo Quantification of Hip Arthrokinematics during Dynamic Weight-bearing Activities using Dual Fluoroscopy

In Vivo Quantification of Hip Arthrokinematics during Dynamic Weight-bearing Activities using Dual Fluoroscopy

Published on: July 2, 2021

An Inertial Measurement Unit Based Method to Estimate Hip and Knee Joint Kinematics in Team Sport Athletes on the Field

An Inertial Measurement Unit Based Method to Estimate Hip and Knee Joint Kinematics in Team Sport Athletes on the Field

Published on: May 26, 2020

Related Concept Videos

Functional Classification of Joints

Functional Classification of Joints

Functional Classification of Joints
The functional classification of joints is determined by the amount of mobility between the adjacent bones. Joints are functionally classified as a synarthrosis or immobile joint, an amphiarthrosis or slightly moveable joint, or as a diarthrosis, a freely moveable joint. Fibrous and cartilaginous joints can be functionally classified as either synarthroses or amphiarthroses, whereas all synovial joints are classified as diarthroses.
Synarthrosis
An...

Articulations of the Vertebral Column

Articulations of the Vertebral Column

In addition to being held together by the intervertebral discs, adjacent vertebrae also articulate with each other at synovial joints formed between the superior and inferior articular processes called zygapophysial joints (facet joints). These are plane joints that provide for only limited motions between the vertebrae. The orientation of the articular processes at these joints varies in different regions of the vertebral column and serves to determine the types of motions available in each...

Anatomical Positions

Anatomical Positions

In anatomy, several standard anatomical positions are used as references for describing the position and orientation of different body parts. These positions help provide a common frame of reference when discussing anatomical structures. The anatomical position is the standard reference point for describing the body's position and orientation. In this position:
The body is upright, facing forward, and standing erect.
The feet are parallel and flat on the floor.
The arms are hanging by the...

Development of the Limb Synovial Joints

Development of the Limb Synovial Joints

Joints form during embryonic development in conjunction with the formation and growth of the associated bones. The embryonic tissue that gives rise to all bones, cartilage, and connective tissues of the body is called mesenchyme.
The mesenchymal stem cells differentiate into chondrocytes that form the hyaline cartilage, and later the cartilaginous model of the bone. This model further transforms into a bone. This process is known as endochondral ossification.
During development, the limbs...

Joints

Joints

Joints, also called articulations or articular surfaces, are points at which ligaments or other tissues connect adjacent bones. Joints permit movement and stability, and can be classified based on their structure or function.
Structural joint classifications are based on the material that makes up the joint as well as whether or not the joint contains a space between the bones. Joints are structurally classified as fibrous, cartilaginous, or synovial.
Fibrous Joints Are Immovable
The bones of a...

Knee Joint

Knee Joint

The knee joint is the most complicated joint in the body. It consists of three articulations– two tibiofemoral and one patellofemoral. As is characteristic of synovial joints, the knee joint has a thin articular capsule that partially surrounds this joint cavity. Additionally, several ligaments, muscles, and cartilaginous structures support the movement of the knee.
A total of seven ligaments support the knee joint. The patellar ligament, which is also attached to the quadriceps femoris...

Articles linked to this work by shared authors, journal, and citation graph.

TAL, encoding a transaldolase, increases grain size and promotes grain filling in rice.

Journal of advanced research·2026

A comparative study on percutaneous vertebroplasty for osteoporotic vertebral compression fractures under day surgery and inpatient management models.

Frontiers in surgery·2026

Development and evaluation of a modified injectable calcium phosphate cement with enhanced injectability and mechanical stability for bone defect repair.

BMC musculoskeletal disorders·2026

Low-Profile Posterior Lumbar Fusion Combined With Proximal Interlaminar Coflex Dynamic Fixation for Lumbar Degenerative Diseases: A Comparative Study.

Orthopaedic surgery·2026

The ZFP36/ZFP252-OsDOG1L1-OsPP2Cs module regulates seed germination in rice.

Journal of integrative plant biology·2026

Expression of miR-27a in Patients with Steroid-associated Femoral Head Osteonecrosis and Its Regulatory Mechanism on Proliferation and Osteogenic Differentiation of Bone Marrow Mesenchymal Stem Cells.

Journal of musculoskeletal & neuronal interactions·2026

See all related articles