Related Experiment Video

Updated: Aug 15, 2025

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators
11:44

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators

Published on: August 15, 2014

10.4K

A Capacitive DC-DC Boost Converter with Gate Bias Boosting and Dynamic Body Biasing for an RF Energy Harvesting

Jiho Jung1, Ickjin Kwon1

  • 1Department of Electrical and Computer Engineering, Ajou University, Suwon 16499, Republic of Korea.

Sensors (Basel, Switzerland)
|January 8, 2023
PubMed

Keywords:
DC-DC converterRF energy harvestingboost convertercharge pumphigh efficiency

More Related Videos

X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells10:16

X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells

Published on: August 20, 2019

13.9K
In Situ Transmission Electron Microscopy with Biasing and Fabrication of Asymmetric Crossbars Based on Mixed-Phased a-VOx09:49

In Situ Transmission Electron Microscopy with Biasing and Fabrication of Asymmetric Crossbars Based on Mixed-Phased a-VOx

Published on: May 13, 2020

4.1K

Related Concept Videos

Biasing of FET01:22

Biasing of FET

Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the...
339
Biasing of Metal-Semiconductor Junctions01:27

Biasing of Metal-Semiconductor Junctions

Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
305
Biasing of P-N Junction01:16

Biasing of P-N Junction

The operation of a p-n junction diode involves various biasing conditions, including forward bias, reverse bias, and equilibrium.
In equilibrium, no external voltage is applied across the p-n junction. The depletion region is formed at the junction interface due to the diffusion of carriers, which leaves behind charged dopants, acceptors on the p-side, and donors on the n-side. These immobile charges create an electric field that prevents further diffusion of carriers. The related energy band...
686
Design Example: Capacitance Multiplier Circuit01:20

Design Example: Capacitance Multiplier Circuit

In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
895
MOSFET Amplifiers01:17

MOSFET Amplifiers

The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
207
RC Circuits: Charging A Capacitor01:30

RC Circuits: Charging A Capacitor

A circuit containing resistance and capacitance is called an RC circuit. A capacitor is an electrical component that stores electric charge by storing energy in an electric field. Consider a simple RC circuit having a DC (direct current) voltage source ε, a resistor R, a capacitor C, and a two-way position switch. In the circuit, the capacitor can be charged or discharged depending on the position of the switch.
When the switch is moved to connect the battery, the circuit reduces to a simple...
3.7K