Related Experiment Video

Updated: Aug 12, 2025

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180° Curved Artery Test Section
11:00

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180° Curved Artery Test Section

Published on: July 19, 2016

11.7K

Entropy analysis for a novel peristaltic flow in a curved heated endoscope: an application of applied sciences

Sohail Nadeem1,2, Salman Akhtar3, Anber Saleem4

  • 1Department of Mathematics, Quaid-i-Azam University 45320, Islamabad, 44000, Pakistan. sohail@qau.edu.pk.

Scientific Reports
|January 27, 2023
PubMed

More Related Videos

Assembly and Characterization of an External Driver for the Generation of Sub-Kilohertz Oscillatory Flow in Microchannels08:32

Assembly and Characterization of an External Driver for the Generation of Sub-Kilohertz Oscillatory Flow in Microchannels

Published on: January 28, 2022

2.4K
Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow08:25

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow

Published on: April 30, 2018

7.2K

Related Concept Videos

Steady, Laminar Flow in Circular Tubes01:23

Steady, Laminar Flow in Circular Tubes

Hagen-Poiseuille flow describes a viscous fluid's steady, incompressible flow through a cylindrical tube with a constant radius R. This flow profile is often applied to understand fluid transport in narrow channels, such as capillaries. It serves as a foundational example of laminar flow. In this model, cylindrical coordinates (r,θ,z) are used to describe the radial (r), angular (θ), and axial (z) dimensions within the tube. For Hagen-Poiseuille flow, the velocity profile is...
298
Application of the Linear Momentum Equation01:15

Application of the Linear Momentum Equation

The application of the linear momentum equation can be used to analyze the forces needed to hold a 180-degree pipe bend in place with flowing water. In this case, water flows through the bend with a constant cross-sectional area of 0.01 square meters and a flow velocity of 15 meters per second. The pressure at the entrance is 0.2 Megapascals and the pressure at the exit is 0.16 Megapascals.
The goal is to determine the force components in the x and y directions to hold the pipe in place. Since...
124
Bernoulli's Equation for Flow Normal to a Streamline01:16

Bernoulli's Equation for Flow Normal to a Streamline

Bernoulli's equation for flow normal to a streamline explains how pressure varies across curved streamlines due to the outward centrifugal forces induced by the fluid's curvature. The pressure is higher on the inner side of the curve, near the center of curvature, and decreases outward to balance these centrifugal forces.
The pressure difference depends on the fluid's velocity and radius of curvature. The pressure variation is minimal in flows with nearly straight streamlines.
927
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution...
223
Couette Flow01:22

Couette Flow

Couette flow represents the flow of fluid between two parallel plates, with one plate fixed and the other moving with a constant velocity. This configuration allows for a simplified analysis using the Navier-Stokes equations, which govern fluid motion under conditions of viscosity and incompressibility. For Couette flow, the assumptions include a steady, laminar, incompressible flow with a zero-pressure gradient in the flow direction. This flow type is beneficial for understanding shear-driven...
371
Steady, Laminar Flow Between Parallel Plates01:17

Steady, Laminar Flow Between Parallel Plates

Understanding steady, laminar flow between parallel plates is essential for analyzing and designing flow in narrow rectangular channels, commonly found in various water conveyance and drainage systems. The Navier-Stokes equations govern fluid motion and are generally challenging to solve due to their nonlinearity. However, simplifications are possible in certain cases, like the steady laminar flow between parallel plates. For this scenario, we assume steady, incompressible, laminar flow.
271