Related Experiment Video

Updated: Jul 18, 2025

Author Spotlight: Advancing Anaerobic Microbiota Research Using a Novel Respirometry Protocol
06:11

Author Spotlight: Advancing Anaerobic Microbiota Research Using a Novel Respirometry Protocol

Published on: April 26, 2024

1.3K

Site suitability analysis for locating construction and demolition waste transfer station: an Indian case study

H Devaki1, S Shanmugapriya2

  • 1Department of Civil Engineering, Coimbatore Institute of Technology, Coimbatore, Tamil Nadu, 641014, India. devakihalan23@gmail.com.

Environmental Monitoring and Assessment
|August 24, 2023
PubMed

Keywords:
Analytic hierarchy process (AHP)Geographic Information System (GIS)Multi-criteria analysisSite suitability analysisWaste managementWaste transfer station

More Related Videos

Design and Construction of an Urban Runoff Research Facility13:48

Design and Construction of an Urban Runoff Research Facility

Published on: August 8, 2014

13.1K
The Microscopy-Based Assay to Study and Analyze the Recycling Endosomes using SNARE Trafficking08:51

The Microscopy-Based Assay to Study and Analyze the Recycling Endosomes using SNARE Trafficking

Published on: February 12, 2022

3.6K

Related Concept Videos

Design Example: Aggregate Gradation01:24

Design Example: Aggregate Gradation

The right type and quality of aggregates are crucial for concrete as they significantly influence its properties, mix proportions, and cost-effectiveness. If different sources are available for sand, the commonly used fine aggregate in concrete, the selection of sand is primarily based on its gradation.
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is...
119
Sieve Analysis and Grading Curves01:19

Sieve Analysis and Grading Curves

Sieve analysis is a method used to determine the particle size distribution of aggregate materials. This process involves the following steps:
413
Design Example: Sustainability in Concrete Building01:26

Design Example: Sustainability in Concrete Building

As the construction industry moves towards more eco-friendly practices, concrete's adaptability and its ability to incorporate sustainable features make it a key material in the drive towards greener building solutions.
There are multiple approaches to achieve sustainability in a commercial concrete building. For instance, construct a concrete parking area under the building, utilizing pervious concrete paver blocks in open areas to facilitate rainwater collection through an underground...
188
Design Example: Managing Concrete Workability01:14

Design Example: Managing Concrete Workability

This example deals with managing the workability of concrete for a raft foundation project under hot weather conditions. Workability is crucial for ensuring the concrete is easy to place, compact, and finish. In this scenario, a slump test — a common method to measure the workability of fresh concrete — initially indicated low workability. This was attributed to the rapid water loss from the concrete mix, exacerbated by the high temperatures causing the course aggregates to heat up.
101
Design Example: Analyzing Capacity Contours for Flood Risk Assessment01:17

Design Example: Analyzing Capacity Contours for Flood Risk Assessment

Flood risk assessment involves careful planning and analysis to ensure the safety of communities near water retention structures. Capacity contours are a vital tool in this process, as they illustrate the potential spread of water at specific levels in a given area. In the context of building a bund across a small valley, these contours play a critical role in evaluating the safety of nearby residential areas.In this example, the bund is intended to store stormwater in the valley. The engineers...
70
Deleterious Substances in Aggregate01:25

Deleterious Substances in Aggregate

Deleterious substances in aggregates can be detrimental to the quality and durability of concrete. These substances include organic impurities like loam, which interfere with cement hydration and are usually present in the sand. These prevent a good bond between aggregate and cement paste. Organic impurities can be detected using the colorimetric test, where the darkness of a solution after agitation indicates the level of organic content.
Another type of impurity is clay and fine material that...
191