Related Experiment Video

Updated: Jul 12, 2025

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements
14:18

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements

Published on: February 28, 2016

11.5K

Phase stability diagram, self-similar structures, and multistability in a free-running VCSEL with a small

Shuangquan Gu, Pei Zhou, Penghua Mu

    Optics Express
    |October 20, 2023
    PubMed

    More Related Videos

    Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator08:39

    Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator

    Published on: January 28, 2019

    9.8K
    Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities11:08

    Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities

    Published on: November 30, 2012

    19.0K

    Related Concept Videos

    Oscillations In An LC Circuit01:30

    Oscillations In An LC Circuit

    An idealized LC circuit of zero resistance can oscillate without any source of emf by shifting the energy stored in the circuit between the electric and magnetic fields. In such an LC circuit, if the capacitor contains a charge q before the switch is closed, then all the energy of the circuit is initially stored in the electric field of the capacitor. This energy is given by
    2.3K
    Small-Signal Analysis of MOSFET Amplifiers01:23

    Small-Signal Analysis of MOSFET Amplifiers

    In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
    576
    Biasing of Metal-Semiconductor Junctions01:27

    Biasing of Metal-Semiconductor Junctions

    Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
    In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
    261
    IR Spectrum Peak Splitting: Symmetric vs Asymmetric Vibrations01:08

    IR Spectrum Peak Splitting: Symmetric vs Asymmetric Vibrations

    Identical bonds within a polyatomic group can stretch symmetrically (in-phase) or asymmetrically (out-of-phase). Similar to hydrogen bonding, these vibrations also influence the shape of the IR peak. Generally, asymmetric stretching frequencies are higher than symmetric stretching frequencies. For example, primary amines exhibit two distinct IR peaks between 3300–3500 cm−1 corresponding to the symmetric and asymmetric N-H stretching, while secondary amines exhibit a single...
    1.0K
    Stability of Equilibrium Configuration01:23

    Stability of Equilibrium Configuration

    Understanding the stability of equilibrium configurations is a fundamental part of mechanical engineering. In any system, there are three distinct types of equilibrium: stable, neutral, and unstable.
    A stable equilibrium occurs when a system tends to return to its original position when given a small displacement, and the potential energy is at its minimum. An example of a stable equilibrium is when a cantilever beam is fixed at one end and a weight is attached to the other end. If the weight...
    455