Related Experiment Video

Updated: Aug 6, 2026

A System to Create Stable Nanoparticle Aerosols from Nanopowders
12:59

A System to Create Stable Nanoparticle Aerosols from Nanopowders

Published on: July 26, 2016

9.6K

Evaluation of a Three-Fluid Nozzle Spraying Process for Facilitating Spray Drying of Hydrophilic Polymers for the

Lena Karin Mueller1, Laura Halstenberg1, Nicole Di Gallo1

  • 1Merck Life Science KGaA, Frankfurter Straße 250, 64293 Darmstadt, Germany.

Pharmaceutics
|November 25, 2023
PubMed

Keywords:
amorphous solid dispersionpolyvinyl alcoholprocess developmentspray dryingspray-dried dispersionsustainabilityspray drying pharmaceuticalsamorphous drug formulationspolyvinyl alcohol excipientdrug solubility enhancement

More Related Videos

Flash NanoPrecipitation for the Encapsulation of Hydrophobic and Hydrophilic Compounds in Polymeric Nanoparticles10:12

Flash NanoPrecipitation for the Encapsulation of Hydrophobic and Hydrophilic Compounds in Polymeric Nanoparticles

Published on: January 7, 2019

22.1K
Frugal Imaging Technique of Capillary Flow Through Three-Dimensional Polymeric Printing Powders06:01

Frugal Imaging Technique of Capillary Flow Through Three-Dimensional Polymeric Printing Powders

Published on: October 4, 2022

1.3K

Related Concept Videos

Fineness of Cement01:15

Fineness of Cement

The fineness of cement directly influences the rate of hydration, as the hydration begins at the surface of the cement particles. In addition to hydration, the fineness of cement is vital for various properties of concrete including workability, gypsum requirement, and long-term behavior. The fineness of cement is represented in terms of the specific surface of cement which is typically measured in square meters per kilogram, with several methods available for this determination.
Direct...
Shotcrete01:18

Shotcrete

Shotcrete is a specialized technique where mortar or small aggregate concrete rich in cement content is sprayed onto a surface at high velocity. The force of impact compacts the material and enables it to cling to vertical or overhead areas without sagging. The technique involves layering the shotcrete in stages until it reaches approximately 4 inches in thickness. Operator skill in nozzle management is pivotal in deciding the quality of the shotcrete. Shotcrete is used in constructing tunnel...
Design Example: Managing Concrete Workability01:14

Design Example: Managing Concrete Workability

This example deals with managing the workability of concrete for a raft foundation project under hot weather conditions. Workability is crucial for ensuring the concrete is easy to place, compact, and finish. In this scenario, a slump test — a common method to measure the workability of fresh concrete — initially indicated low workability. This was attributed to the rapid water loss from the concrete mix, exacerbated by the high temperatures causing the course aggregates to heat up.
To address...
Surface Tension of Fluid01:22

Surface Tension of Fluid

Surface tension is a fundamental property of fluids, occurring at the boundary between a liquid and a gas or between two immiscible liquids. This phenomenon arises from the cohesive forces between molecules at the fluid's surface, creating an effect similar to a stretched elastic membrane. Inside each fluid, molecules are equally attracted in all directions by neighboring molecules, but surface molecules experience a net inward force, resulting in surface tension.
Surface tension varies with...
Pipe Flowrate Measurement: Problem Solving01:28

Pipe Flowrate Measurement: Problem Solving

A spray tank system is engineered to uniformly distribute a pest-control liquid across plants by using a pressurized mechanism. The tank, pressurized to 150 kPa, holds the pesticide at a height of 0.80 meters. Liquid flows from the tank through a 1.9 meter pipe with a diameter of 0.015 meters, angled at 0.698 radians, ultimately reaching a 0.007 meter nozzle that sprays the pesticide. Accurate calculation of the system's flow rate is crucial to ensure uniform application, and this is achieved...