Related Experiment Video

Updated: Jul 5, 2025

Data Communication Based on MQTT in a Polymer Extrusion Process
08:15

Data Communication Based on MQTT in a Polymer Extrusion Process

Published on: July 15, 2022

3.5K

Modbus Extension Server Implementation for BIoT-Enabled Smart Switch Embedded System Device

Vasile Gheorghiță Găitan1,2, Ionel Zagan1,2

  • 1Faculty of Electrical Engineering and Computer Science, Stefan cel Mare University, 720229 Suceava, Romania.

Sensors (Basel, Switzerland)
|January 23, 2024
PubMed

Keywords:
Building Internet of ThingsModbus extensionacquisition cyclecommunicationremote terminal unit (RTU)server

More Related Videos

Integration of 5G Experimentation Infrastructures into a Multi-Site NFV Ecosystem10:15

Integration of 5G Experimentation Infrastructures into a Multi-Site NFV Ecosystem

Published on: February 3, 2021

3.8K
Autonomous and Rechargeable Microneurostimulator Endoscopically Implantable into the Submucosa08:17

Autonomous and Rechargeable Microneurostimulator Endoscopically Implantable into the Submucosa

Published on: September 27, 2018

8.5K

Related Concept Videos

Power System Distribution01:25

Power System Distribution

Power system distribution involves delivering electrical energy from power plants to consumers through a network of transmission and distribution systems. The process begins at power plants, where energy from coal, gas, nuclear, water, and wind is converted into electrical energy. These plants use three-phase generators, typically rated between 50 to 1300 MVA, with terminal voltages ranging from a few kV to 20 kV, depending on the size and age of the units.
The transmission system is designed...
240
Switching of BJT01:22

Switching of BJT

Switching behavior in Bipolar Junction Transistors (BJTs) is a fundamental aspect utilized in various electronic circuits, particularly for digital logic applications like switches and amplifiers. In a typical switching circuit, a BJT alternates between cut-off and saturation modes, corresponding to the "off" and "on" states, respectively, thus behaving like an ideal switch.
Cut-off Mode ("Off" State): In this state, both the emitter-base and collector-base junctions are...
421
PI Controller: Design01:24

PI Controller: Design

Proportional Integral (PI) controllers are a fundamental component in modern control systems, widely used to enhance performance and mitigate steady-state errors. They are particularly effective in applications such as automatic brightness adjustment on smartphones, where they excel at mitigating steady-state errors for step-function inputs. Unlike PD controllers, which require time-varying errors to function optimally, PI controllers leverage their integral component to address residual...
280
Bus Impedance Matrix01:24

Bus Impedance Matrix

Calculating subtransient fault currents for three-phase faults in an N-bus power system involves using the positive-sequence network. When a three-phase short circuit occurs at a specific bus, the analysis uses the superposition method to evaluate two separate circuits.
In the first circuit, all machine voltage sources are short-circuited, leaving only the prefault voltage source at the fault location. The positive-sequence bus impedance matrix can be determined by solving the nodal equations,...
122
Differential Relays01:20

Differential Relays

Differential relays are used to protect generators, buses, and transformers by comparing electrical quantities at different points. When a fault occurs, the difference in current between the two points triggers the relay to operate, opening the circuit breaker. Under normal conditions, the current entering (i1) and leaving (i2) a generator are equal. When a fault occurs, however, these currents become unequal, and the difference current flows in the relay operating coil, causing the relay to...
138
Overcurrent Relays01:26

Overcurrent Relays

Overcurrent relays, crucial for circuit protection, are connected to the secondary current of a current transformer. There are two primary types of overcurrent relays: instantaneous and time-delay.
Instantaneous overcurrent relays activate immediately when the input current exceeds a predetermined value, known as the pickup current, instantly energizing the circuit breaker trip coil. This rapid response is vital for addressing severe faults quickly.
Time-delay overcurrent relays, on the other...
86