Related Experiment Video

Updated: Jul 3, 2025

Experimental Investigation of the Hierarchical Control in DC Microgrids Using a Real-time Simulator
06:04

Experimental Investigation of the Hierarchical Control in DC Microgrids Using a Real-time Simulator

Published on: February 14, 2025

359

Great Britain's power system with a high penetration of renewable energy: Dataset supporting future scenarios

K Guerra1,2, A Welfle2,3, R Gutiérrez-Alvarez4

  • 1Chemical and Environmental Engineering Department, Escuela Técnica Superior de Ingeniería, Universidad de Sevilla. Camino de los Descubrimientos s/n, 41092 Seville, Spain.

Data in Brief
|February 13, 2024
PubMed

Keywords:
BiomassCurtailmentDecarbonisationHydrogenHydrogen storagePower sectorVariable renewable energy

More Related Videos

Using Generative Art to Convey Past and Future Climate Transitions06:10

Using Generative Art to Convey Past and Future Climate Transitions

Published on: March 31, 2023

961
Design, Instrumentation and Usage Protocols for Distributed In Situ Thermal Hot Spots Monitoring in Electric Coils using FBG Sensor Multiplexing10:52

Design, Instrumentation and Usage Protocols for Distributed In Situ Thermal Hot Spots Monitoring in Electric Coils using FBG Sensor Multiplexing

Published on: March 8, 2020

5.9K

Related Concept Videos

Power System Distribution01:25

Power System Distribution

Power system distribution involves delivering electrical energy from power plants to consumers through a network of transmission and distribution systems. The process begins at power plants, where energy from coal, gas, nuclear, water, and wind is converted into electrical energy. These plants use three-phase generators, typically rated between 50 to 1300 MVA, with terminal voltages ranging from a few kV to 20 kV, depending on the size and age of the units.
The transmission system is designed...
239
Maximum Power Flow and Line Loadability01:23

Maximum Power Flow and Line Loadability

The maximum power flow for lossy transmission lines is derived using ABCD parameters in phasor form. These parameters create a matrix relationship between the sending-end and receiving-end voltages and currents, allowing the determination of the receiving-end current. This relationship facilitates calculating the complex power delivered to the receiving end, from which real and reactive power components are derived.
116
Electrical Power01:07

Electrical Power

Electric power is the product of current and voltage, represented in units of joules per second, or watts. For example, cars often have one or more auxiliary power outlets with which you can charge a cell phone or other electronic devices. These outlets may be rated at 20 amps and 12 volts, so that the circuit can deliver a maximum power of 240 watts. Consider a 25 Watt bulb and a 60 Watt bulb. The conversion of electrical energy produces heat and light, while the kinetic energy lost by the...
3.1K
Energy and Power Signals01:17

Energy and Power Signals

In an electrical system with a resistor, voltage and current signals facilitate the measurement of power and energy across the resistor. For a continuous-time signal, the total energy over a time interval is defined as the integral of the square of the signal's magnitude over that interval. Mathematically, this is expressed as:
294
Power and Energy01:12

Power and Energy

The power and energy delivered to an element are subjects of great significance in the field of electrical engineering. It is a well-known fact that a 100-watt light bulb emits more light than a 60-watt one. Therefore, power and energy calculations play a crucial role in the analysis of electrical circuits.
Power, defined as the time rate of expending or absorbing energy, is quantified in units called watts (W). The relation between power and energy is mathematically given as
800
Secondary Distribution01:25

Secondary Distribution

Secondary distribution systems provide electrical energy at the utilization voltage levels from distribution transformers to customer meters. Typical secondary voltages in the United States include 120/240 V for residential use, 208Y/120 V for residential and commercial use, and 480Y/277 V for industrial and high-rise commercial use.
In residential areas, 120/240 V single-phase, three-wire service is commonly used for lighting, outlets, and large appliances. Urban areas with high-density loads...
85