Related Experiment Video

Updated: May 10, 2026

In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint
07:09

In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint

Published on: March 7, 2014

13.4K

Temporomandibular joint stress analysis of patients with different mandibular deformities during unilateral molar

Chongke Zheng1,2, Jingheng Shu1,2, Bingmei Shao2,3

  • 1Key Lab for Biomechanical Engineering of Sichuan Province, Sichuan University, Chengdu, China.

Computer Methods in Biomechanics and Biomedical Engineering
|June 4, 2024
PubMed

Keywords:
Finite element analysismandibular deformitiestemporomandibular disorder (TMD)temporomandibular joint (TMJ)unilateral molar occlusion

More Related Videos

Author Spotlight: 3D Movement Assessment of Maxillary Posterior Teeth in Clear Aligner Treatment07:32

Author Spotlight: 3D Movement Assessment of Maxillary Posterior Teeth in Clear Aligner Treatment

Published on: February 23, 2024

1.1K
Temporomandibular Joint Pain Measurement by Bite Force and Von Frey Filament Assays in Mice06:37

Temporomandibular Joint Pain Measurement by Bite Force and Von Frey Filament Assays in Mice

Published on: September 13, 2024

910

Related Concept Videos

Method of Joints: Problem Solving I01:30

Method of Joints: Problem Solving I

The method of joints is a commonly used technique to analyze the forces in structural trusses. The method is based on the principle of equilibrium, which assumes that the truss members are connected by frictionless pins. The forces at each joint can be determined by considering the equilibrium of the forces acting on that joint. Consider a truss structure with two forces of 20 N and 10 N acting at joints C and D, respectively. The method of joints can be used to determine the forces FCB, FDC,...
Method of Joints: Problem Solving II01:30

Method of Joints: Problem Solving II

Consider a truss structure with frictionless joints fixed to a wall and roller support. If a force of 150 N is applied to joint A, the forces in each member of the truss can be determined using the method of joints.
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added together...
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
Bending of Curved Members - Strain Analysis01:14

Bending of Curved Members - Strain Analysis

The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
The important part of bending analysis for such a member is the...