Related Experiment Video
Updated: Jun 23, 2025
Production of Single Tracks of Ti-6Al-4V by Directed Energy Deposition to Determine the Layer Thickness for Multilayer Deposition
Published on: March 13, 2018
A Comparative Analysis of Low and High SiC Volume Fraction Additively Manufactured SiC/Ti6Al4V(ELI) Composites Based
Masenate Thamae1, Maina Maringa1, Willie du Preez2
1Department of Mechanical and Mechatronics Engineering, Faculty of Engineering, Built Environment and Information Technology, Central University of Technology, Bloemfontein 9301, Free State, South Africa.
Abstract:
Silicon carbide (SiC) exhibits intriguing thermo-physical properties such as higher heat capacity and conductivity, as well as a lower density than Ti6Al4V(ELI). These properties make SiC a good candidate for the reinforcement of Ti6Al4V(ELI) with respect to its use as a heat shield in aero turbines to increase their efficiency. The traditional materials used in aircraft structures were required to have a combination of good mechanical properties such as strength, stiffness, and hardness and low weight, as well as low thermo-physical properties such as coefficient of thermal expansion (CTE) and thermal conductivity. The alloy Ti6Al4V(ELI) has a density of 4.45 g/cm3, which is lower than that of structural steel (7.4 g/cm3) and higher than that of aluminium (2.5 g/cm3). Lower density benefits light weighting. Aluminium is the lightest of the traditional materials used but has relatively low strength. The CTE of SiC of 4.6 × 10-6/K is lower than that of Ti6Al4V(ELI) of 8.6 × 10-6/K, while the density of SiC of 3.21 g/cm3 is lower than that of Ti6Al4V(ELI) of 4.45 g/cm3. Therefore, from the theory of composites, SiC/Ti6Al4V(ELI) composites are expected to have lower densities and CTEs than those of Ti6Al4V(ELI), thus providing for lightweighting and less thermal related buckling or separation at their joints with carbon/epoxy resin panels. The specific strength, stiffness, and Knoop hardness of SiC of 75-490 kNm/kg, 132 MNm/kg, and 600-3800 GPa, respectively, are generally larger than those of Ti6Al4V(ELI) of 211 KNm/kg, 24 MNm/kg, and 880 GPa, respectively. Therefore, investigating reinforcement of Ti6Al4V(ELI) with SiC particles is worthwhile as it will lead to the formation of composites that are stronger, stiffer, harder, and lighter, with lower values of CTE. For additive manufacturing, this requires initial studies to optimise the process parameters of laser power and scanning speed for single tracks. To print single tracks in the present work, different laser powers ranging from 100 W to 350 W and scanning speeds ranging from 0.3 m/s to 2.7 m/s were used for different SiC volume fraction values of values. To print single layers, different values of hatch distance were used together with the best values of laser power and scanning speed determined elsewhere by the authors for different volume fractions of SiC. Through optical microscopy, the built tracks and their cross sections were examined. By using laser power and scanning speeds of 200 W and 1.2 m/s, and 150 W and 0.8 m/s, respectively, the best tracks at 5% and 10% volume fractions were obtained, whereas the best tracks at 25% volume fraction were achieved using a laser power of 200 W and a scanning speed of 0.5 m/s. Furthermore, the results showed that the maximum SiC volume percentage of 30% resulted in limited or no penetration. Therefore, it is concluded from the study that parts with improved mechanical properties can be produced at SiC volume fractions ranging from 5% to 25%, while parts produced at the high volume fraction of 30% would have unacceptable mechanical qualities for the final part.
