Related Experiment Video

Updated: Jun 14, 2025

Application of Design Aspects in Uniaxial Loading Machine Development
05:23

Application of Design Aspects in Uniaxial Loading Machine Development

Published on: September 19, 2018

5.8K

Buckling behaviour of rectangular and skew plates with elastically restrained edges under non-uniform mechanical edge

Chen Wang1, Qiang Liu1

  • 1AVIC General Huanan Aircraft Industry Co., Ltd, Zhuhai, China.

Plos One
|September 6, 2024
PubMed

More Related Videos

Cutting Procedures, Tensile Testing, and Ageing of Flexible Unidirectional Composite Laminates07:53

Cutting Procedures, Tensile Testing, and Ageing of Flexible Unidirectional Composite Laminates

Published on: April 27, 2019

8.2K
Determination of the Mechanical Properties of Flexible Connectors for Use in Insulated Concrete Wall Panels05:26

Determination of the Mechanical Properties of Flexible Connectors for Use in Insulated Concrete Wall Panels

Published on: October 19, 2022

1.6K

Related Concept Videos

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
253
Eccentric Axial Loading in a Plane of Symmetry01:16

Eccentric Axial Loading in a Plane of Symmetry

Eccentric axial loading occurs when an axial load is applied away from the centroidal axis of a structural member. This scenario is common in engineering, where structural elements may not be directly aligned due to various design or functional requirements.
175
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
94
Eccentric Loading01:16

Eccentric Loading

Eccentric loading is a crucial concept in the study of structural engineering and mechanics, particularly when analyzing the stability and stress distribution in columns. Unlike centric loading, where the force is applied along the centroidal axis, causing uniform compression, eccentric loading occurs when a force is applied off-center. This off-center application introduces not only direct compressive stress but also bending stress, significantly influencing the column's behavior under...
331
Residual Stresses in Bending01:18

Residual Stresses in Bending

In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
153
General Case of Eccentric Axial Loading01:12

General Case of Eccentric Axial Loading

Unsymmetrical bending occurs when the bending moment applied to a structural member does not align with its principal axis. This misalignment leads to complex stress distributions and deflection patterns that differ from symmetrical bending, which are essential for designing structures to withstand different loading conditions.
Consider a member subjected to equal and opposite forces that are applied along a line that does not coincide with the member's neutral axis. In unsymmetrical...
180