Related Experiment Video

Updated: Jun 10, 2025

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators
11:44

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators

Published on: August 15, 2014

10.3K

Semi-Global Stabilization of Discrete-Time Linear Systems Subject to Infinite Distributed Input Delays and Actuator

Yige Guo, Xiang Xu, Lu Liu

    IEEE Transactions on Cybernetics
    |October 11, 2024
    PubMed

    More Related Videos

    WheelCon: A Wheel Control-Based Gaming Platform for Studying Human Sensorimotor Control08:18

    WheelCon: A Wheel Control-Based Gaming Platform for Studying Human Sensorimotor Control

    Published on: August 15, 2020

    4.9K
    Interactive and Visualized Online Experimentation System for Engineering Education and Research08:35

    Interactive and Visualized Online Experimentation System for Engineering Education and Research

    Published on: November 24, 2021

    2.4K

    Related Concept Videos

    Linear Approximation in Time Domain01:21

    Linear Approximation in Time Domain

    Nonlinear systems often require sophisticated approaches for accurate modeling and analysis, with state-space representation being particularly effective. This method is especially useful for systems where variables and parameters vary with time or operating conditions, such as in a simple pendulum or a translational mechanical system with nonlinear springs.
    For a simple pendulum with a mass evenly distributed along its length and the center of mass located at half the pendulum's length,...
    68
    Second Order systems II01:18

    Second Order systems II

    In an underdamped second-order system, where the damping ratio ζ is between 0 and 1, a unit-step input results in a transfer function that, when transformed using the inverse Laplace method, reveals the output response. The output exhibits a damped sinusoidal oscillation, and the difference between the input and output is termed the error signal. This error signal also demonstrates damped oscillatory behavior. Eventually, as the system reaches a steady state, the error diminishes to zero.
    92
    BIBO stability of continuous and discrete -time systems01:24

    BIBO stability of continuous and discrete -time systems

    System stability is a fundamental concept in signal processing, often assessed using convolution. For a system to be considered bounded-input bounded-output (BIBO) stable, any bounded input signal must produce a bounded output signal. A bounded input signal is one where the modulus does not exceed a certain constant at any point in time.
    To determine the BIBO stability, the convolution integral is utilized when a bounded continuous-time input is applied to a Linear Time-Invariant (LTI) system....
    355
    Stability01:28

    Stability

    The time response of a linear time-invariant (LTI) system can be divided into transient and steady-state responses. The transient response represents the system's initial reaction to a change in input and diminishes to zero over time. In contrast, the steady-state response is the behavior that persists after the transient effects have faded.
    The stability of an LTI system is determined by the roots of its characteristic equation, known as poles. A system is stable if it produces a bounded...
    94
    Feedback control systems01:26

    Feedback control systems

    Feedback control systems are categorized in various ways based on their design, analysis, and signal types.
    Linear feedback systems are theoretical models that simplify analysis and design. These systems operate under the principle that their output is directly proportional to their input within certain ranges. For instance, an amplifier in a control system behaves linearly as long as the input signal remains within a specific range. However, most physical systems exhibit inherent nonlinearity...
    293
    Linear time-invariant Systems01:23

    Linear time-invariant Systems

    A system is linear if it displays the characteristics of homogeneity and additivity, together termed the superposition property. This principle is fundamental in all linear systems. Linear time-invariant (LTI) systems include systems with linear elements and constant parameters.
    The input-output behavior of an LTI system can be fully defined by its response to an impulsive excitation at its input. Once this impulse response is known, the system's reaction to any other input can be...
    222