Related Experiment Video

Updated: Jun 5, 2025

Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior
10:52

Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior

Published on: April 13, 2016

8.7K

Corrigendum: How general is the natural frequency effect? The case of joint probabilities

Nathalie Stegmüller1, Karin Binder2, Stefan Krauss1

  • 1Mathematics Education, Faculty of Mathematics, University of Regensburg, Regensburg, Germany.

Frontiers in Psychology
|December 4, 2024
PubMed
Summary

This study corrects a previous article DOI. The corrected DOI is 10.3389/fpsyg.2024.1296359, ensuring proper citation and access to the research findings.

Keywords:
Bayesian reasoningjoint probabilitiesnatural frequenciesnet diagramvisualization

More Related Videos

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion09:32

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion

Published on: April 11, 2018

9.7K
Oscillation and Reaction Board Techniques for Estimating Inertial Properties of a Below-knee Prosthesis08:08

Oscillation and Reaction Board Techniques for Estimating Inertial Properties of a Below-knee Prosthesis

Published on: May 8, 2014

16.7K

Related Concept Videos

Functional Classification of Joints01:09

Functional Classification of Joints

Functional Classification of Joints
The functional classification of joints is determined by the amount of mobility between the adjacent bones. Joints are functionally classified as a synarthrosis or immobile joint, an amphiarthrosis or slightly moveable joint, or as a diarthrosis, a freely moveable joint. Fibrous and cartilaginous joints can be functionally classified as either synarthroses  or amphiarthroses, whereas all synovial joints are classified as diarthroses.
Synarthrosis
An...
3.8K
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
249
Forced Oscillations01:06

Forced Oscillations

When an oscillator is forced with a periodic driving force, the motion may seem chaotic. The motions of such oscillators are known as transients. After the transients die out, the oscillator reaches a steady state, where the motion is periodic, and the displacement is determined.
6.5K
Determination of Expected Frequency01:08

Determination of Expected Frequency

Suppose one wants to test independence between the two variables of a contingency table. The values in the table constitute the observed frequencies of the dataset. But how does one determine the expected frequency of the dataset? One of the important assumptions is that the two variables are independent, which means the variables do not influence each other. For independent variables, the statistical probability of any event involving both variables is calculated by multiplying the individual...
2.1K
Expected Frequencies in Goodness-of-Fit Tests01:19

Expected Frequencies in Goodness-of-Fit Tests

A goodness-of-fit test is conducted to determine whether the observed frequency values are statistically similar to the frequencies expected for the dataset. Suppose the expected frequencies for a dataset are equal such as when predicting the frequency of any number appearing when casting a die. In that case, the expected frequency is the ratio of the total number of observations (n)  to the number of categories (k).
2.5K
Frequency of Spring-Mass System01:17

Frequency of Spring-Mass System

One interesting characteristic of the simple harmonic motion (SHM) of an object attached to a spring is that the angular frequency, and the period and frequency of the motion, depend only on the mass and the force constant of the spring, and not on other factors such as the amplitude of the motion or initial conditions. We can use the equations of motion and Newton's second law to find the angular frequency, frequency, and period.
Consider a block on a spring on a frictionless surface. There...
5.3K