Related Experiment Video

Updated: May 7, 2025

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes
11:05

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes

Published on: December 13, 2016

12.1K

Preliminary validation for an online configuration determination method of a thin film buckling under point contact

Yeoun-Jae Kim1, Daehan Wi2

  • 1Biomedical Engineering Research Center, Asan Institute for Life Sciences, Asan Medical Center, 88, Olympic-ro 43-gil, Songpa-gu, Seoul, 05505, South Korea.

Scientific Reports
|December 31, 2024
PubMed

Keywords:
Ansys simulationBuckling configurationConstrained optimizationExperimentPoint contact forceStaticsThin film

More Related Videos

Applying Dynamic Strain on Thin Oxide Films Immobilized on a Pseudoelastic Nickel-Titanium Alloy09:35

Applying Dynamic Strain on Thin Oxide Films Immobilized on a Pseudoelastic Nickel-Titanium Alloy

Published on: July 28, 2020

4.9K
Structural Design and Manufacturing of a Cruiser Class Solar Vehicle14:57

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle

Published on: January 30, 2019

13.7K

Related Concept Videos

Euler's Formula for Pin-Ended Columns01:21

Euler's Formula for Pin-Ended Columns

In structural engineering, the stability of columns under compressive axial loads is a critical consideration, described as buckling. A typical example involves a column PQ, which is pin-connected at both ends and subjected to a centric axial load F applied at one end, with a reaction force of F' = -F at the other end. Here, it is crucial to understand that when an applied load exceeds the critical load, buckling occurs as the system becomes unstable.
To calculate the critical load,...
261
Yield Criteria for Ductile Materials under Plane Stress01:25

Yield Criteria for Ductile Materials under Plane Stress

In designing structural elements and machine parts using ductile materials, it is crucial to ensure that these components withstand applied stresses without yielding. Yielding is initially determined through a tensile test, which evaluates the material's response to uniaxial stress. However, tensile stress is insufficient when components face biaxial or plane stress conditions This condition requires advanced criteria to predict failure.
The Maximum Shearing Stress Criterion, also known as...
124
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
121
Method of Sections: Problem Solving II01:30

Method of Sections: Problem Solving II

Consider an arbitrary truss structure composed of diagonal, vertical, and horizontal members fixed to the wall. To calculate the force acting on members CB, GB, and GH, method of sections can be used. The loads and lengths of the horizontal and vertical members are known parameters, as shown in the figure.
859
Euler's Formula to Columns: Problem Solving01:23

Euler's Formula to Columns: Problem Solving

Euler's formula is used in structural engineering to determine the buckling load of columns under various conditions. However, when dealing with systems that incorporate both rigid elements and elastic components, such as springs, the analysis requires a finer approach to determine the critical load. The problem described involves two rigid bars connected at a pivot point with a spring attached and a vertical load applied at one end.
The system comprises two vertical rigid bars, AB and BC,...
124
Castigliano's Theorem: Problem Solving01:14

Castigliano's Theorem: Problem Solving

The deflection of a simply supported beam that carries a central point load can be analyzed using structural mechanics principles, particularly by applying Castigliano's theorem. This theorem relates the displacement at the load application point to the partial derivatives of the strain energy in the structure. The simply supported beam with a point load at its center has symmetric reaction forces at the supports, each bearing half of the load. The bending moment at any point along the beam...
508