Related Experiment Video

Updated: May 21, 2025

Force System with Vertical V-Bends: A 3D In Vitro Assessment of Elastic and Rigid Rectangular Archwires
08:46

Force System with Vertical V-Bends: A 3D In Vitro Assessment of Elastic and Rigid Rectangular Archwires

Published on: July 24, 2018

10.5K

Influence of attachment position and torque overcorrection on arch expansion in clear aligner treatment: a

Ziwei Tang, Hu Long, Lu Liu

    The Angle Orthodontist
    |March 19, 2025
    PubMed
    Abstract

    Keywords:
    Clear alignerExpansionFinite elementOvercorrection

    More Related Videos

    Author Spotlight: 3D Movement Assessment of Maxillary Posterior Teeth in Clear Aligner Treatment07:32

    Author Spotlight: 3D Movement Assessment of Maxillary Posterior Teeth in Clear Aligner Treatment

    Published on: February 23, 2024

    989
    Author Spotlight: Development of a Novel Finite Element Analysis Model for Improved Orthognathic Surgical Techniques07:16

    Author Spotlight: Development of a Novel Finite Element Analysis Model for Improved Orthognathic Surgical Techniques

    Published on: October 20, 2023

    1.2K

    Related Concept Videos

    Stress Concentrations in Circular Shafts01:18

    Stress Concentrations in Circular Shafts

    Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
    155
    General Case of Eccentric Axial Loading01:12

    General Case of Eccentric Axial Loading

    Unsymmetrical bending occurs when the bending moment applied to a structural member does not align with its principal axis. This misalignment leads to complex stress distributions and deflection patterns that differ from symmetrical bending, which are essential for designing structures to withstand different loading conditions.
    Consider a member subjected to equal and opposite forces that are applied along a line that does not coincide with the member's neutral axis. In unsymmetrical...
    163
    Eccentric Axial Loading in a Plane of Symmetry01:16

    Eccentric Axial Loading in a Plane of Symmetry

    Eccentric axial loading occurs when an axial load is applied away from the centroidal axis of a structural member. This scenario is common in engineering, where structural elements may not be directly aligned due to various design or functional requirements.
    152
    Net Torque Calculations01:19

    Net Torque Calculations

    When a mechanic tries to remove a hex nut with a wrench, it is easier if the force is applied at the farthest end of the wrench handle. The lever arm is the distance from the pivot point (the hex nut in this case) to the person’s hand. If this distance is large, the torque is higher. Only the component of the force perpendicular to the lever arm contributes to the torque. Therefore, pushing the wrench perpendicular to the lever arm is more advantageous. If multiple people apply force to...
    9.0K
    Thin-Walled Hollow Shafts01:15

    Thin-Walled Hollow Shafts

    In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution...
    159
    Residual Stresses in Circular Shafts01:10

    Residual Stresses in Circular Shafts

    In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
    149