Related Experiment Video

Updated: Sep 26, 2026

Self-assembling Morphologies Obtained from Helical Polycarbodiimide Copolymers and Their Triazole Derivatives
09:22

Self-assembling Morphologies Obtained from Helical Polycarbodiimide Copolymers and Their Triazole Derivatives

Published on: February 7, 2017

Right-handed and left-handed helices of poly(dA-dC) X (dG-dT)

J A Taboury, E Taillandier

    Nucleic Acids Research
    |June 25, 1985
    PubMed

    More Related Videos

    Drawing and Hydrophobicity-patterning Long Polydimethylsiloxane Silicone Filaments07:56

    Drawing and Hydrophobicity-patterning Long Polydimethylsiloxane Silicone Filaments

    Published on: January 7, 2019

    Tactile Semiautomatic Passive-Finger Angle Stimulator (TSPAS)04:40

    Tactile Semiautomatic Passive-Finger Angle Stimulator (TSPAS)

    Published on: July 30, 2020

    Related Concept Videos

    Thermal Electrocyclic Reactions: Stereochemistry01:17

    Thermal Electrocyclic Reactions: Stereochemistry

    The stereochemistry of electrocyclic reactions is strongly influenced by the orbital symmetry of the polyene HOMO. Under thermal conditions, the reaction proceeds via the ground-state HOMO.
    Selection Rules: Thermal Activation
    Conjugated systems containing an even number of π-electron pairs undergo a conrotatory ring closure. For example, thermal electrocyclization of (2E,4E)-2,4-hexadiene, a conjugated diene containing two π-electron pairs, gives trans-3,4-dimethylcyclobutene.
    Induced Electric Dipoles01:29

    Induced Electric Dipoles

    A permanent electric dipole orients itself along an external electric field. This rotation can be quantified by defining the potential energy because the external torque does work in rotating it. Then, the potential energy is minimum at the parallel configuration and maximum at the antiparallel configuration. While the former is a stable equilibrium, the latter is an unstable equilibrium.
    Since the absolute value of potential energy holds no physical meaning, its zero value can be chosen as per...
    Force On A Current Loop In A Magnetic Field01:17

    Force On A Current Loop In A Magnetic Field

    Magnetic forces on wires carrying current are most frequently applied in motors. A DC motor is a device that converts electrical energy into mechanical work. In motors, wire loops are enclosed in a magnetic field. When current flows through the loops, the magnetic field applies torque, which causes the shaft to rotate. The direction of the current is reversed once the loop's surface area is lined up with the magnetic field, causing a constant torque on the loop. During the process, commutators...
    DC Generator01:19

    DC Generator

    An alternator converts mechanical energy into electrical energy that varies sinusoidally, resulting in AC current. Meanwhile, a DC generator converts mechanical energy into electrical energy, which are DC pulses with the same polarity. The construction of a DC generator is similar to that of an alternator, except that the pair of slip rings is replaced by a single split ring, also called a commutator. The commutator functions like a periodic rotary switch; it changes the contacts with the...
    Method of Sections: Problem Solving I01:27

    Method of Sections: Problem Solving I

    Consider a symmetrical roof truss structure, composed of vertical, diagonal, and horizontal members. The length of each horizontal member is 4 m. The lengths of the vertical members FB and HD are 4 m, while the length of member GC is 6 m. The loads acting at joints F, G, and H are 2 kN, while those at joints A and E are 1 kN.
    Angle of Twist: Problem Solving01:13

    Angle of Twist: Problem Solving

    An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the torque exerted...