Related Experiment Video

Updated: May 16, 2025

Fabrication and Testing of Microfluidic Optomechanical Oscillators
09:10

Fabrication and Testing of Microfluidic Optomechanical Oscillators

Published on: May 29, 2014

12.1K

Inverse design fiber-to-chip couplers for the O- and C-bands: publisher's note

Julian Pita, Paulo Dainese, Michaël Ménard

    Optics Letters
    |April 1, 2025
    PubMed

    More Related Videos

    Design and Fabrication of an Optical Fiber Made of Water08:06

    Design and Fabrication of an Optical Fiber Made of Water

    Published on: November 8, 2018

    8.1K
    Multicolor Fluorescence Detection for Droplet Microfluidics Using Optical Fibers10:21

    Multicolor Fluorescence Detection for Droplet Microfluidics Using Optical Fibers

    Published on: May 5, 2016

    10.4K

    Related Concept Videos

    Transmission Line Design Considerations01:23

    Transmission Line Design Considerations

    Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
    108
    Design Example01:23

    Design Example

    The innovation of touch-tone telephony revolutionized the telecommunications industry by replacing the traditional rotary dial with a dual-tone multi-frequency (DTMF) signaling system. This system uses a matrix-style keypad with buttons arranged in four rows and three columns, creating 12 distinct signals each assigned to a pair of frequencies. Each button press results in a simultaneous generation of two sinusoidal tones – one from a low-frequency group (697 to 941 Hz) and one from a...
    309
    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    633
    Mesh Analysis for AC Circuits01:12

    Mesh Analysis for AC Circuits

    In the domain of radio communication, the significance of impedance matching must be considered. It is crucial to ensure the efficient transmission of signals between radio transmitters and receivers. Achieving this balance involves using impedance-matching circuits, with one fundamental configuration comprising a resistor, capacitor, and inductor.
    The process of harmonizing these impedances begins with a clear understanding of the input and output signals. Once these signals are known, the...
    317
    Cascaded Op Amps01:16

    Cascaded Op Amps

    Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
    In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
    545
    Energy Stored In A Coaxial Cable01:31

    Energy Stored In A Coaxial Cable

    A coaxial cable consists of a central copper conductor used for transmitting signals, followed by an insulator shield, a metallic braided mesh that prevents signal interference, and a plastic layer that encases the entire assembly.
    In the simplest form, a coaxial cable can be represented by two long hollow concentric cylinders in which the current flows in opposite directions. The magnetic field inside and outside the coaxial cable is determined by using Ampère's law. The magnetic...
    1.3K