Related Experiment Video

Updated: Jan 17, 2026

Optimized Fabrication Procedure for High-Quality Graphene-based Moiré Superlattice Devices
11:24

Optimized Fabrication Procedure for High-Quality Graphene-based Moiré Superlattice Devices

Published on: July 11, 2025

16.0K

Design and investigation of a polarization convertor loaded MIMO graphene-silicon DRA in the THz domain with enhanced

Vivek Singh Kushwah, M Lakshmi Narasimha Charyulu, M Ramana Reddy

    Applied Optics
    |September 22, 2025
    PubMed

    More Related Videos

    In Situ Transmission Electron Microscopy with Biasing and Fabrication of Asymmetric Crossbars Based on Mixed-Phased a-VOx09:49

    In Situ Transmission Electron Microscopy with Biasing and Fabrication of Asymmetric Crossbars Based on Mixed-Phased a-VOx

    Published on: May 13, 2020

    4.4K
    Simulation, Fabrication and Characterization of THz Metamaterial Absorbers13:44

    Simulation, Fabrication and Characterization of THz Metamaterial Absorbers

    Published on: December 27, 2012

    15.9K

    Related Concept Videos

    MOSFET: Enhancement Mode01:22

    MOSFET: Enhancement Mode

    Enhancement-mode MOSFETs are pivotal components in electronics, distinguished by their capacity to act as highly efficient switches. They are part of the larger family of metal-oxide Semiconductor Field-Effect Transistors (MOSFETs). They are available in two types: p-channel and n-channel, each tailored to specific polarity operations.
    In their basic form, enhancement-mode MOSFETs are typically non-conductive when the gate-source voltage (Vgs) is zero. This default 'off' state means no...
    792
    Biasing of Metal-Semiconductor Junctions01:27

    Biasing of Metal-Semiconductor Junctions

    Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
    In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
    555
    Induced Electric Dipoles01:28

    Induced Electric Dipoles

    A permanent electric dipole orients itself along an external electric field. This rotation can be quantified by defining the potential energy because the external torque does work in rotating it. Then, the potential energy is minimum at the parallel configuration and maximum at the antiparallel configuration. While the former is a stable equilibrium, the latter is an unstable equilibrium.
    Since the absolute value of potential energy holds no physical meaning, its zero value can be chosen as per...
    4.7K
    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    1.5K
    Biasing of P-N Junction01:16

    Biasing of P-N Junction

    The operation of a p-n junction diode involves various biasing conditions, including forward bias, reverse bias, and equilibrium.
    In equilibrium, no external voltage is applied across the p-n junction. The depletion region is formed at the junction interface due to the diffusion of carriers, which leaves behind charged dopants, acceptors on the p-side, and donors on the n-side. These immobile charges create an electric field that prevents further diffusion of carriers. The related energy band...
    1.8K
    MOSFET Amplifiers01:17

    MOSFET Amplifiers

    The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
    494