Related Experiment Video

Updated: Jan 17, 2026

Demonstration of Equal-Intensity Beam Generation by Dielectric Metasurfaces
09:33

Demonstration of Equal-Intensity Beam Generation by Dielectric Metasurfaces

Published on: June 7, 2019

6.6K

Design of spliced dual-band reconfigurable metasurface for wireless communications and power transfer

Heng Zhou, Dexiao Xia, Peitong He

    Optics Express
    |September 23, 2025
    PubMed

    More Related Videos

    Demonstration of Spin-Multiplexed and Direction-Multiplexed All-Dielectric Visible Metaholograms08:48

    Demonstration of Spin-Multiplexed and Direction-Multiplexed All-Dielectric Visible Metaholograms

    Published on: September 25, 2020

    6.2K
    Simulation, Fabrication and Characterization of THz Metamaterial Absorbers13:44

    Simulation, Fabrication and Characterization of THz Metamaterial Absorbers

    Published on: December 27, 2012

    15.9K

    Related Concept Videos

    Maximum Power Transfer01:16

    Maximum Power Transfer

    Numerous practical applications within engineering disciplines, such as telecommunications, necessitate optimizing power delivery to a connected load. This pursuit, however, entails inherent internal losses, which can either equal or exceed the power supplied to the load. The Thevenin equivalent circuit is helpful in finding the maximum power a linear circuit can deliver to a load. It is assumed in this context that the load resistance can be adjusted.
    By substituting the entire circuit with...
    828
    Mesh Analysis for AC Circuits01:12

    Mesh Analysis for AC Circuits

    In the domain of radio communication, the significance of impedance matching must be considered. It is crucial to ensure the efficient transmission of signals between radio transmitters and receivers. Achieving this balance involves using impedance-matching circuits, with one fundamental configuration comprising a resistor, capacitor, and inductor.
    The process of harmonizing these impedances begins with a clear understanding of the input and output signals. Once these signals are known, the...
    669
    Transmission Line Design Considerations01:23

    Transmission Line Design Considerations

    Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
    601
    The Maximum Power Transfer Theorem01:20

    The Maximum Power Transfer Theorem

    Consider a linear AC Thevenin equivalent circuit connected to a load impedance.
    The load connected draws the current, and the circuit delivers the power to the load. The alternating current flowing through the load is determined using the rectangular form of voltages, currents, network impedance, and load impedance. The average power delivered to the load is obtained from the product of the square of current and load resistance.
    1.1K
    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    1.5K
    Biasing of Metal-Semiconductor Junctions01:27

    Biasing of Metal-Semiconductor Junctions

    Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
    In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
    555