Related Experiment Video

Updated: Jan 12, 2026

Production and Analysis of Sporosarcina pasteurii Biocement Bricks Using Custom 3D-Printed Molds for Unconfined Compression Tests
05:38

Production and Analysis of Sporosarcina pasteurii Biocement Bricks Using Custom 3D-Printed Molds for Unconfined Compression Tests

Published on: March 7, 2025

847

A Comparison of Various Cementation Methods for the Retention of Prefabricated Posts: An Original Research

Pramod Punchiri Sadan1, Smita Durga Dutta2

  • 1Department of Prosthetic Dental Sciences, Qassim University, Al Mulaydah, Qassim, Saudi Arabia.

Journal of Pharmacy & Bioallied Sciences
|October 30, 2025
PubMed
Abstract

Keywords:
Endodontically treated teethluting cementsprefabricated postsresin cementretention strength

More Related Videos

Installation Method to Enhance Quality Control for Fiber Reinforced Polymer Spike Anchors06:21

Installation Method to Enhance Quality Control for Fiber Reinforced Polymer Spike Anchors

Published on: April 10, 2018

7.4K
An Improved Mechanical Testing Method to Assess Bone-implant Anchorage11:51

An Improved Mechanical Testing Method to Assess Bone-implant Anchorage

Published on: February 10, 2014

15.9K

Related Concept Videos

Ferrocement01:30

Ferrocement

Ferro-cement is a distinctive construction material that represents an innovative variant of reinforced concrete, characterized by its unique composition and the method by which it is formed. Unlike standard reinforced concrete, which relies on larger steel bars for reinforcement, ferro-cement utilizes densely packed layers of mesh or fine rods, fully encased in cement mortar. This composition allows for the creation of structures that are significantly thinner and more flexible than their...
696
Posttensioned Masonry Walls01:15

Posttensioned Masonry Walls


Post-tensioned masonry walls use high-strength steel rods or flexible tendons to enhance the strength and efficiency of masonry structures. These elements are securely anchored to the foundation and extend vertically either within the cores of the masonry units or between the masonry wythes. The construction process involves building the wall with these tensioning elements in place and allowing the mortar to fully cure.
Following the curing process, the tensioning begins. Steel rods are...
446
Strength of Cement01:20

Strength of Cement

Strength tests for cement are not performed directly on neat cement paste due to difficulty in obtaining consistent, reliable specimens. Instead, cement is typically tested in the form of cement-sand mortar.
For compressive strength tests, ASTM C 109-05 standards prescribe a cement-sand mix ratio of 1:2.75 and a water/cement ratio of 0.485 for making 2-inch cubes. These cubes are mixed, cast, and cured in saturated lime water at 23°C until testing. Flexural strength testing, outlined in...
440
Prestressed Concrete01:20

Prestressed Concrete

Prestressed concrete is a construction technique designed to enhance the strength and durability of concrete structures. This method involves the application of a pre-set tension to high-strength steel strands used as reinforcement before the concrete is subjected to its working loads. The primary aim of prestressing is to place the concrete in a state of compression, in order to counteract the tensile forces it will experience in service. This pre-compression helps prevent crack formation in...
732
Preplaced Aggregate Concrete01:29

Preplaced Aggregate Concrete

Preplaced aggregate concrete is ideal for construction environments that are not easily accessible. The process begins by properly wetting the gap-graded coarse aggregates to remove the dirt, then placing it in the form and compacting it. Voids are filled with a mortar mix pumped under pressure through slotted pipes. This mortar typically consists of Portland cement, pozzolan, fine aggregates, water, and a fluidizing aid. The pozzolan helps reduce bleeding and segregation while improving the...
361
Setting Time of Cement01:12

Setting Time of Cement

The setting time of cement refers to the process of cement paste transitioning from a plastic state to a solid state. This process is crucial in construction as it dictates the timeframe for concrete placement, compaction, and finishing. The onset of this solidification is termed the initial set, indicating when the paste becomes unworkable. The final set is when the paste has solidified completely, and further handling or manipulation can no longer affect its shape. The cement strength is...
574