Related Experiment Video

Updated: Feb 15, 2026

Synthesis and Microdiffraction at Extreme Pressures and Temperatures
07:26

Synthesis and Microdiffraction at Extreme Pressures and Temperatures

Published on: October 7, 2013

11.7K

Control of Anion Ordering in Perovskite Oxyhydrides by High-Pressure and High-Temperature Treatment

Takafumi Yamamoto1,2, Haruki Tochizawa2, Teppei Nagase1,2

  • 1Department of Chemistry, Graduate School of Science, Kyoto University, Kitashirakawa Oiwake-cho, Sakyoku, Kyoto, 606-8502, Japan.

Inorganic Chemistry
|February 13, 2026
PubMed

More Related Videos

Detection of Viruses from Bioaerosols Using Anion Exchange Resin06:10

Detection of Viruses from Bioaerosols Using Anion Exchange Resin

Published on: August 22, 2018

8.7K
Low Pressure Vapor-assisted Solution Process for Tunable Band Gap Pinhole-free Methylammonium Lead Halide Perovskite Films08:12

Low Pressure Vapor-assisted Solution Process for Tunable Band Gap Pinhole-free Methylammonium Lead Halide Perovskite Films

Published on: September 8, 2017

10.1K

Related Concept Videos

Physical Methods for Controlling Microbial Growth: Temperature01:23

Physical Methods for Controlling Microbial Growth: Temperature

Heat is a widely used method to control microbial growth by targeting and denaturing cellular proteins, thereby killing or inactivating microbes. This method's effectiveness is quantified using parameters such as the thermal death point (TDP), thermal death time (TDT), and decimal reduction time (D value). TDP represents the lowest temperature at which all microorganisms in a liquid suspension are eliminated within 10 minutes, whereas TDT is the time necessary to achieve sterilization at a...
1.2K
Vapor Pressure02:34

Vapor Pressure

When a liquid vaporizes in a closed container, gas molecules cannot escape. As these gas phase molecules move randomly about, they will occasionally collide with the surface of the condensed phase, and in some cases, these collisions will result in the molecules re-entering the condensed phase. The change from the gas phase to the liquid is called condensation. When the rate of condensation becomes equal to the rate of vaporization, neither the amount of the liquid nor the amount of the vapor...
41.1K
Aromatic Hydrocarbon Anions: Structural Overview01:18

Aromatic Hydrocarbon Anions: Structural Overview

Neutral hydrocarbons like cyclopentadiene with an odd number of carbon atoms and one intervening CH2 group in the ring are not aromatic. Cyclopentadiene with 4 π electrons does not satisfy the 4n + 2 π electron rule. Additionally, the intervening CH2 group is sp3 hybridized and lacks a vacant p orbital, thereby interrupting the overlap of p orbitals in a continuous manner and preventing the delocalization of π electrons throughout the ring.
Due to the absence of continuous...
3.9K
Effects of Temperature on Free Energy02:11

Effects of Temperature on Free Energy

The spontaneity of a process depends upon the temperature of the system. Phase transitions, for example, will proceed spontaneously in one direction or the other depending upon the temperature of the substance in question. Likewise, some chemical reactions can also exhibit temperature-dependent spontaneities. To illustrate this concept, the equation relating free energy change to the enthalpy and entropy changes for the process is considered:
28.5K
Anionic Chain-Growth Polymerization: Overview01:20

Anionic Chain-Growth Polymerization: Overview

The polymerization process that involves carbanion as an intermediate is called anionic polymerization. It is also a type of addition or chain-growth polymerization. Anionic polymerization gets initiated by a strong nucleophile such as an organolithium or a Grignard reagent. The most commonly used initiator for anionic polymerization is butyl lithium. Monomers involved in anionic polymerization must possess a vinyl group bonded to one or two electron-withdrawing groups. For instance,...
2.6K
Anionic Chain-Growth Polymerization: Mechanism01:04

Anionic Chain-Growth Polymerization: Mechanism

The mechanism for anionic chain-growth polymerization involves initiation, propagation, and termination steps. In the initiation step, a nucleophilic anion, such as butyl lithium, initiates the polymerization process by attacking the π bond of the vinylic monomer. As a result, a carbanion, stabilized by the electron‐withdrawing group, is generated. The resulting carbanion acts as a Michael donor in the propagation step and attacks the second vinylic monomer, which acts as a Michael...
2.5K