Interplay of stoichiometry and crystallization kinetics in vapor-based hybrid perovskite film growth

Related Experiment Video

Updated: Mar 4, 2026

Influence of Hybrid Perovskite Fabrication Methods on Film Formation, Electronic Structure, and Solar Cell Performance
11:38

Influence of Hybrid Perovskite Fabrication Methods on Film Formation, Electronic Structure, and Solar Cell Performance

Published on: February 27, 2017

19.1K

Xingyu Ren1, Mimi Fu1, Xiaoyu Wu1

  • 1School of Physics and Optoelectronic Engineering, Hainan University, Haikou, Hainan, 570228, China. ruiguo@hainanu.edu.cn.

Nanoscale
|March 3, 2026
PubMed

More Related Videos

Epitaxial Growth of Perovskite Strontium Titanate on Germanium via Atomic Layer Deposition09:45

Epitaxial Growth of Perovskite Strontium Titanate on Germanium via Atomic Layer Deposition

Published on: July 26, 2016

12.9K
Flash Infrared Annealing for Perovskite Solar Cell Processing05:15

Flash Infrared Annealing for Perovskite Solar Cell Processing

Published on: February 3, 2021

8.7K

Related Concept Videos

Crystal Growth: Principles of Crystallization01:25

Crystal Growth: Principles of Crystallization

Crystallization is a phase transformation process in which crystals are precipitated from a supersaturated solution or formed from other sources. During crystallization, atoms or molecules arrange themselves into a well-defined, rigid crystal lattice to minimize energy.
Initiating crystallization involves manipulating the concentration of the solute and the temperature of the solution. Since crystal growth occurs when the ratio of concentration and solubility of the solute in the solvent...
5.5K
Recrystallization: Solid–Solution Equilibria01:10

Recrystallization: Solid–Solution Equilibria

Recrystallization is a purification technique used to separate impurities from solid compounds. In this technique, no chemical reactions occur. Instead, it exploits physical properties only, specifically, the solubility differences between the desired compound and impurities, either at a single temperature or at different temperatures, and under other selected conditions. The solid-solution equilibrium (solubility equilibrium) of each component in the solution represents a binary phase...
4.2K
Precipitation Processes01:12

Precipitation Processes

The experimental conditions in a gravimetric analysis should be optimized to maximize the particle size and purity of the obtained precipitate. Ideally, the concentration of the precipitating reagent should be low with effective stirring to maintain low relative supersaturation for the growth of large crystals. In homogeneous precipitation, the precipitant is slowly generated by a chemical reaction in the solution to avoid local reagent excesses. For example, urea decomposes gradually to...
6.4K
Precipitate Formation and Particle Size Control01:16

Precipitate Formation and Particle Size Control

In precipitation gravimetry, the precipitating agent should react specifically or selectively with the analyte. While a specific reagent reacts with the analyte alone, a selective reagent can react with a limited number of chemical species.
The obtained precipitate should be either a pure substance of known composition or easily converted to one by a simple process, such as ignition or drying. In addition, the precipitate should be insoluble and easily filterable. In general, filterability...
6.9K
Phase Transitions: Vaporization and Condensation02:39

Phase Transitions: Vaporization and Condensation

The physical form of a substance changes on changing its temperature. For example, raising the temperature of a liquid causes the liquid to vaporize (convert into vapor). The process is called vaporization—a surface phenomenon. Vaporization occurs when the thermal motion of the molecules overcome the intermolecular forces, and the molecules (at the surface) escape into the gaseous state. When a liquid vaporizes in a closed container, gas molecules cannot escape. As these gas phase molecules...
21.8K
Washing, Drying, and Ignition of Precipitates00:52

Washing, Drying, and Ignition of Precipitates

After filtration, the precipitate is washed to remove coprecipitated impurities and any remaining mother liquor. Colloidal precipitates, such as silver chloride, are washed with an electrolyte (such as dilute nitric acid) to prevent the peptization of the precipitate. In the case of slightly soluble precipitates, the wash solution contains a common ion to reduce solubility. Lead sulfate, which is slightly soluble in water, is washed with dilute sulfuric acid. Similarly, wash solutions may be...
6.9K