Related Experiment Video

Updated: Apr 15, 2026

Precision Measurements and Parametric Models of Vertebral Endplates
10:35

Precision Measurements and Parametric Models of Vertebral Endplates

Published on: September 17, 2019

6.9K

The influence of passive spinal structures on spinal geometric compensation during flexion-extension: A finite

Adi Mithani1, Ahmed Aoude2, Mark Driscoll1

  • 1Musculoskeletal Biomechanics Research Lab, Department of Mechanical Engineering, McGill University, 845 Sherbrooke St. W, Montréal, Quebec, H3A 0C3, Canada; Orthopaedic Research Lab, Montreal General Hospital, 1650 Cedar Ave (LS1.409), Montreal, Quebec, H3G 1A4, Canada.

Journal of the Mechanical Behavior of Biomedical Materials
|April 13, 2026
PubMed

Keywords:
Biological tissuesBiomechanicsFinite element analysisMechanical propertiesSpine

More Related Videos

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion09:32

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion

Published on: April 11, 2018

10.5K
Lateral-PLIF for Lumbar Spinal Arthrodesis: A Detailed Step-By-Step Surgical Technique08:36

Lateral-PLIF for Lumbar Spinal Arthrodesis: A Detailed Step-By-Step Surgical Technique

Published on: January 23, 2026

290

Related Concept Videos

Eccentric Axial Loading in a Plane of Symmetry01:16

Eccentric Axial Loading in a Plane of Symmetry

Eccentric axial loading occurs when an axial load is applied away from the centroidal axis of a structural member. This scenario is common in engineering, where structural elements may not be directly aligned due to various design or functional requirements.
728
Vertebral Column: Regions and Curvature01:16

Vertebral Column: Regions and Curvature

The vertebral column or spine is a flexible column that supports the head, neck, and body and  allows for their movements. It also protects the spinal cord.
Regions of the Vertebral Column
In an adult, the spine is subdivided into five regions: the cervical, the thoracic, the lumbar, the sacral, and the coccygeal region. The spine initially develops as a series of 33 vertebrae; after 20 years of age, the nine bones in the sacral region, five sacral, and four coccygeal bones fuse to form...
12.0K
Plastic Deformations of Members with a Single Plane of Symmetry01:21

Plastic Deformations of Members with a Single Plane of Symmetry

When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
458
Bending of Curved Members - Strain Analysis01:14

Bending of Curved Members - Strain Analysis

The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
The important part of bending analysis for such a member...
663
Flexural Stress01:16

Flexural Stress

When analyzing bending in symmetric members, it's crucial to understand how stresses distribute when subjected to bending moments. This stress distribution is effectively described by applying fundamental mechanics and material science principles, particularly Hooke's Law for elastic materials.
Hooke's Law states that within the material's elastic limits, stress is directly proportional to strain. In a member experiencing a bending moment, the strain at any point is relative to its distance...
903
Bending of Members Made of Several Materials01:11

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
770