Related Experiment Video

Updated: Jun 21, 2026

A Method for Studying the Temperature Dependence of Dynamic Fracture and Fragmentation
09:12

A Method for Studying the Temperature Dependence of Dynamic Fracture and Fragmentation

Published on: June 28, 2015

Experimental simulation investigation on fracture behavior and bolt anchoring mechanism in a circular tunnel under

Yulong Chen1,2,3, Duo Xu4, Junyang Teng5

  • 1State Key Laboratory of Water Resource Protection and Utilization in Coal Mining, Beijing, China. 673054399@qq.com.

Scientific Reports
|June 19, 2026
PubMed

Keywords:
Anchor boltAnchoring mechanismBeddingCircular tunnelSupport

More Related Videos

A Virtual Simulation Experiment of Mechanics: Material Deformation and Failure Based on Scanning Electron Microscopy06:54

A Virtual Simulation Experiment of Mechanics: Material Deformation and Failure Based on Scanning Electron Microscopy

Published on: January 20, 2023

Related Concept Videos

Behavior of Concrete Under Compressive Load01:23

Behavior of Concrete Under Compressive Load

Concrete exhibits specific behaviors under different compressive loads. Understanding this is crucial for understanding its structural integrity. When concrete undergoes uniaxial compression, it tends to develop cracks that run parallel to the direction of the force. These parallel cracks stem from localized tensile stresses that occur perpendicular to the compression direction. Additionally, angled cracks may appear due to the formation of shear planes.
As the concrete specimen fractures under...
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
Plastic Deformation in Circular Shafts01:20

Plastic Deformation in Circular Shafts

When materials are subjected to forces that surpass their yield strength, they undergo a process known as plastic deformation. This results in a permanent alteration or strain in their structure. This concept can be specifically applied to circular shafts, where the deformation leads to a change in its shape. The precise evaluation of this plastic deformation requires understanding the stress distribution within the circular shaft, which is achieved by calculating the maximum shearing stress in...
Stress-Strain Diagram - Brittle Materials01:24

Stress-Strain Diagram - Brittle Materials

Brittle materials, including glass, cast iron, and stone, exhibit unique characteristics. They fracture without considerable change in their elongation rate, indicating that their breaking and ultimate strength are equivalent. Such materials also show lower strain levels at the point of rupture. The failure in brittle materials predominantly results from normal stresses, as evidenced by the rupture created along a surface perpendicular to the applied load. These materials do not display...
Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...