Related Experiment Video

Updated: Aug 10, 2026

Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing
08:54

Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing

Published on: February 13, 2018

Influence of cross-sectional geometry on the wave attenuation performance of floating breakwaters: an experimental

Aya Ashraf1,2, Riham Ezzeldin1, Mahmoud E Saad3,4

  • 1Irrigation and Hydraulics Engineering Department, Faculty of Engineering, Mansoura University, Mansoura, Egypt.

Scientific Reports
|August 8, 2026
PubMed

Keywords:
Coastal protectionCross-sectional geometryFloating breakwatersHydrodynamic performanceTrapezoidal profileTriangular profileWave attenuation

More Related Videos

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions11:51

Visually Based Characterization of the Incipient Particle Motion in Regular Substrates: From Laminar to Turbulent Conditions

Published on: February 22, 2018

Impacts of Free-falling Spheres on a Deep Liquid Pool with Altered Fluid and Impactor Surface Conditions08:49

Impacts of Free-falling Spheres on a Deep Liquid Pool with Altered Fluid and Impactor Surface Conditions

Published on: February 17, 2019

Related Concept Videos

Typical Model Studies01:30

Typical Model Studies

Fluid mechanics model studies often utilize scaled-down systems to predict fluid behavior in full-scale environments, such as river flows, dam spillways, and structures interacting with open surfaces. Maintaining Froude number similarity in river models is crucial, as it replicates surface flow features like wave patterns and velocities.
Design Example: Creating a Hydraulic Model of a Dam Spillway01:21

Design Example: Creating a Hydraulic Model of a Dam Spillway

Scaled hydraulic models of dam spillways provide a practical way to replicate and study the intricate flow dynamics of these structures. Often built to a 1:15 ratio, these models allow for observing critical water behavior, such as velocity distribution, flow patterns, and energy dissipation.
Fluid Pressure over Flat Plate of Constant Width01:05

Fluid Pressure over Flat Plate of Constant Width

When a body is submerged in water, it experiences fluid pressure acting normal on its surface and distributed over its area. For better design structures, it is crucial to determine the magnitude and location of the resultant force acting on the surface. In the case of a rectangular plate of constant width submerged in water, the pressure increases with depth, resulting in a linearly varying trapezoidal pressure distribution from the upper to the lower edge of the plate.
The resultant force...
Weir: Problem Solving01:26

Weir: Problem Solving

Water flow in open channels is often measured using hydraulic structures such as weirs, which allow precise calculation of discharge. In a rectangular channel, flow rates are measured using three types of weirs: rectangular sharp-crested, triangular sharp-crested, and broad-crested. The weir head is set at a fixed height above the channel bottom, simplifying calculations and enabling the relationship between depth and flow rate to be analyzed.For the rectangular sharp-crested weir, the flow...
Types of Damping01:20

Types of Damping

If the amount of damping in a system is gradually increased, the period and frequency start to become affected because damping opposes, and hence slows, the back and forth motion (the net force is smaller in both directions). If there is a very large amount of damping, the system does not even oscillate; instead, it slowly moves toward equilibrium. In brief, an overdamped system moves slowly towards equilibrium, whereas an underdamped system moves quickly to equilibrium but will oscillate about...
Hydraulic Jump: Problem Solving01:16

Hydraulic Jump: Problem Solving

To analyze a hydraulic jump in a rectangular channel with a flow speed of 6 meters per second, follow these steps:Calculate Effective Upstream Velocity:When the downstream gate closes, a hydraulic jump forms, traveling upstream at 2 meters per second. This wave speed combines with the initial channel flow velocity, creating an effective upstream velocity.Identify Flow Velocities Before and After the Hydraulic Jump:Upstream of the hydraulic jump, the effective flow velocity includes both the...