Related Experiment Video

Updated: Oct 10, 2026

Simulating Impacts of Ice Storms on Forest Ecosystems
06:27

Simulating Impacts of Ice Storms on Forest Ecosystems

Published on: June 30, 2020

A strengthening yet less extreme Atlantic-European jet during winter

Stefan Brönnimann1,2, Yuri Brugnara1,2, Patrick Kallabis1,2

  • 1Institute of Geography, University of Bern, Bern, Switzerland.

Nature Geoscience
|October 9, 2026
PubMed

Keywords:
Atmospheric dynamicsAttributionClimate changeProjection and prediction

More Related Videos

Cryogenic Liquid Jets for High Repetition Rate Discovery Science08:34

Cryogenic Liquid Jets for High Repetition Rate Discovery Science

Published on: May 9, 2020

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180° Curved Artery Test Section11:00

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180° Curved Artery Test Section

Published on: July 19, 2016

Related Concept Videos

Variation of Atmospheric Pressure01:18

Variation of Atmospheric Pressure

Change in atmospheric pressure with height is particularly interesting. The decrease in atmospheric pressure with increasing altitude is due to the decreasing gravitational force per unit area as we move away from the surface of the earth.
Assuming the air temperature is constant at a given altitude and that the ideal gas law of thermodynamics describes the atmosphere to a good approximation, one can find the variation of atmospheric pressure with height.
Let p(y) be the atmospheric pressure at...
Masonry in Cold and Hot Weather Conditions01:21

Masonry in Cold and Hot Weather Conditions

In cold weather, masonry construction requires specific precautions to ensure mortar does not freeze before curing, as this can significantly weaken its strength and watertightness. Mortar temperature should be maintained between 60°F and 80°F to support proper hydration and curing. Below 40°F, mortar water must be heated, but should not exceed 120°F as high temperatures can reduce mortar's compressive and bond strength.
Other key practices include keeping masonry units and sand dry and...
Boundary Layer Characteristics01:18

Boundary Layer Characteristics

When a fluid encounters a solid surface, a boundary layer forms due to the interaction between the fluid's motion and the stationary surface. This phenomenon is characterized by a thin region adjacent to the surface where viscous forces dominate, influencing the fluid's velocity profile. The development of the boundary layer begins at the leading edge of the surface and evolves as the fluid moves downstream.As the fluid flows over the surface, friction between the fluid and the wall slows down...
Freezing Point Depression and Boiling Point Elevation01:24

Freezing Point Depression and Boiling Point Elevation

When a non-volatile solute is added to a pure solvent, it results in the lowering of the freezing point of the solvent. This phenomenon is called freezing point depression. The extent to which the freezing point is lowered depends on the molality of the solute -the number of moles of solute per kilogram of solvent and the cryoscopic constant of the solvent.From the plot of chemical potential, μ, against temperature, it is evident that the μ of both solid and liquid solvents decrease with...
Freezing Point Depression and Boiling Point Elevation03:12

Freezing Point Depression and Boiling Point Elevation

Boiling Point Elevation
The boiling point of a liquid is the temperature at which its vapor pressure is equal to ambient atmospheric pressure. Since the vapor pressure of a solution is lowered due to the presence of nonvolatile solutes, it stands to reason that the solution’s boiling point will subsequently be increased. Vapor pressure increases with temperature, and so a solution will require a higher temperature than will pure solvent to achieve any given vapor pressure, including one...
Latitudes and Departures01:27

Latitudes and Departures

Latitudes and departures are essential concepts in surveying, providing a systematic way to analyze the projections of traverse lines. These projections allow surveyors to interpret a line's north-south and east-west components, which are crucial for precisely calculating areas, bearings, and lengths. Latitude is the north-south projection of a line, calculated as the product of the line's length and the cosine of its bearing. Departure, conversely, is the east-west projection obtained by...