Related Experiment Video

Updated: Aug 8, 2026

C-arm-Free Simultaneous OLIF51 and Percutaneous Pedicle Screw Fixation in a Single Lateral Position
12:25

C-arm-Free Simultaneous OLIF51 and Percutaneous Pedicle Screw Fixation in a Single Lateral Position

Published on: September 16, 2022

Unilateral lateral mass compression fractures of the axis

M S Abel, J H Teague

    Skeletal Radiology
    |June 6, 1979
    PubMed

    More Related Videos

    Mouse Lumbar Vertebra Uniaxial Compression Testing with Embedding of the Loading Surface07:52

    Mouse Lumbar Vertebra Uniaxial Compression Testing with Embedding of the Loading Surface

    Published on: December 1, 2023

    Minimally Invasive Treatment for Thoracolumbar Burst Fracture Using Sagittal Alignment Screws and A Trauma Reduction Device04:19

    Minimally Invasive Treatment for Thoracolumbar Burst Fracture Using Sagittal Alignment Screws and A Trauma Reduction Device

    Published on: November 8, 2024

    Related Concept Videos

    Articulations of the Vertebral Column01:28

    Articulations of the Vertebral Column

    In addition to being held together by the intervertebral discs, adjacent vertebrae also articulate with each other at synovial joints formed between the superior and inferior articular processes called zygapophysial joints (facet joints). These are plane joints that provide for only limited motions between the vertebrae. The orientation of the articular processes at these joints varies in different regions of the vertebral column and serves to determine the types of motions available in each...
    Plastic Deformations of Members with a Single Plane of Symmetry01:21

    Plastic Deformations of Members with a Single Plane of Symmetry

    When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
    Eccentric Axial Loading in a Plane of Symmetry01:16

    Eccentric Axial Loading in a Plane of Symmetry

    Eccentric axial loading occurs when an axial load is applied away from the centroidal axis of a structural member. This scenario is common in engineering, where structural elements may not be directly aligned due to various design or functional requirements.
    Unsymmetric Bending - Angle of Neutral Axis01:15

    Unsymmetric Bending - Angle of Neutral Axis

    Unsymmetrical bending occurs when a structural member is subjected to bending moments in a plane that does not align with the member's principal axes. This scenario typically arises in beams and other structural components when loads are applied at non-ideal angles, introducing complexities in stress analysis.
    When a bending moment is applied at an angle θ concerning the vertical axis of a symmetrical member, it can be resolved into components along the member's principal centroidal axes. The...
    General Case of Eccentric Axial Loading01:12

    General Case of Eccentric Axial Loading

    Unsymmetrical bending occurs when the bending moment applied to a structural member does not align with its principal axis. This misalignment leads to complex stress distributions and deflection patterns that differ from symmetrical bending, which are essential for designing structures to withstand different loading conditions.
    Consider a member subjected to equal and opposite forces that are applied along a line that does not coincide with the member's neutral axis. In unsymmetrical bending,...
    Behavior of Concrete Under Compressive Load01:23

    Behavior of Concrete Under Compressive Load

    Concrete exhibits specific behaviors under different compressive loads. Understanding this is crucial for understanding its structural integrity. When concrete undergoes uniaxial compression, it tends to develop cracks that run parallel to the direction of the force. These parallel cracks stem from localized tensile stresses that occur perpendicular to the compression direction. Additionally, angled cracks may appear due to the formation of shear planes.
    As the concrete specimen fractures under...