Related Experiment Video

Updated: Jul 13, 2026

Enabling High Grayscale Resolution Displays and Accurate Response Time Measurements on Conventional Computers
06:50

Enabling High Grayscale Resolution Displays and Accurate Response Time Measurements on Conventional Computers

Published on: February 29, 2012

Design and demonstration of a switching engine for a binary true-time-delay device that uses a white cell

Richard Higgins1, Niru K Nahar, Betty Lise Anderson

  • 1Optimer Photonics, 505 King Avenue, Columbus, Ohio 43201, USA.

Applied Optics
|September 19, 2003
PubMed

More Related Videos

Fabrication of an Optical Cell Dryer for the Spectroscopic Analysis Cells05:37

Fabrication of an Optical Cell Dryer for the Spectroscopic Analysis Cells

Published on: January 8, 2019

High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition05:11

High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition

Published on: June 27, 2025

Related Concept Videos

The Y-to-Delta Circuit01:19

The Y-to-Delta Circuit

A balanced wye-to-delta circuit comprises balanced Y-connected voltage sources and delta-connected loads with no neutral line connection.
The initial step in analyzing a wye-to-delta circuit is to assume a positive phase sequence. These phase voltages are then utilized to calculate the line voltages that occur directly across the delta-connected load impedances. Van, Vbn, and Vcn are the phase voltages in wye, and Vab, Vbc, and Vca are the line voltages for a delta circuit. The relation between...
Design Example: Automobile Ignition System01:14

Design Example: Automobile Ignition System

The automobile's ignition system plays a vital role by ensuring the timely ignition of the fuel-air mixture in each cylinder. This ignition is facilitated by a spark plug, which is composed of two electrodes separated by an air gap. A spark forms across this air gap when a substantial voltage is generated between the electrodes, leading to the ignition of the fuel.
One can generate a large voltage using a car battery of 12 volts with the help of inductors. Inductors are known for opposing rapid...
Design Example: Capacitance Multiplier Circuit01:20

Design Example: Capacitance Multiplier Circuit

In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
Design Example01:23

Design Example

The innovation of touch-tone telephony revolutionized the telecommunications industry by replacing the traditional rotary dial with a dual-tone multi-frequency (DTMF) signaling system. This system uses a matrix-style keypad with buttons arranged in four rows and three columns, creating 12 distinct signals each assigned to a pair of frequencies. Each button press results in a simultaneous generation of two sinusoidal tones – one from a low-frequency group (697 to 941 Hz) and one from a...
Clamper Circuit01:14

Clamper Circuit

A clamper circuit, also known as a DC restorer, represents a specialized variant of the rectifier circuit, notable for its method of taking the output across the diode rather than the capacitor. This configuration lends to several distinctive applications, particularly in handling square wave inputs.
Within this circuit, the diode's orientation prompts the capacitor to charge up to the level of the most negative peak of the input signal. Upon reaching this state, the diode ceases to conduct,...
Switching of BJT01:22

Switching of BJT

Switching behavior in Bipolar Junction Transistors (BJTs) is a fundamental aspect utilized in various electronic circuits, particularly for digital logic applications like switches and amplifiers. In a typical switching circuit, a BJT alternates between cut-off and saturation modes, corresponding to the "off" and "on" states, respectively, thus behaving like an ideal switch.
Cut-off Mode ("Off" State): In this state, both the emitter-base and collector-base junctions are reverse-biased. The...