Related Experiment Video

Updated: Aug 22, 2026

Fabrication and Testing of Microfluidic Optomechanical Oscillators
09:10

Fabrication and Testing of Microfluidic Optomechanical Oscillators

Published on: May 29, 2014

On the flicker noise of ferrite circulators for ultra-stable oscillators

Enrico Rubiola1, Yannick Gruson, Vincent Giordano

  • 1Université Henri Poincaré Ecole Supérieure de Sciences et Technologies de l'Ingénieur de Nancy (ESSTIN) and the Laboratory of Physics of Ionized Media and Applications (LPMIA), Nancy, France. rubiola@esstin.uhp-nancy.fr

IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
|September 4, 2004
PubMed

More Related Videos

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators12:18

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators

Published on: August 5, 2013

Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator07:42

Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator

Published on: December 15, 2021

Related Concept Videos

Oscillations In An LC Circuit01:31

Oscillations In An LC Circuit

An idealized LC circuit of zero resistance can oscillate without any source of emf by shifting the energy stored in the circuit between the electric and magnetic fields. In such an LC circuit, if the capacitor contains a charge q before the switch is closed, then all the energy of the circuit is initially stored in the electric field of the capacitor. This energy is given by
RLC Circuit as a Damped Oscillator01:30

RLC Circuit as a Damped Oscillator

An RLC circuit combines a resistor, inductor, and capacitor, connected in a series or parallel combination.
Consider a series RLC circuit. Here, the presence of resistance in the circuit leads to energy loss due to joule heating in the resistance. Therefore, the total electromagnetic energy in the circuit is no longer constant and decreases with time. Since the magnitude of charge, current, and potential difference continuously decreases, their oscillations are said to be damped. This is...
Design Example: Underdamped Parallel RLC Circuit01:17

Design Example: Underdamped Parallel RLC Circuit

Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
Starting with a fixed...
Forced Oscillations01:06

Forced Oscillations

When an oscillator is forced with a periodic driving force, the motion may seem chaotic. The motions of such oscillators are known as transients. After the transients die out, the oscillator reaches a steady state, where the motion is periodic, and the displacement is determined.
Damped Oscillations01:07

Damped Oscillations

In the real world, oscillations seldom follow true simple harmonic motion. A system that continues its motion indefinitely without losing its amplitude is termed undamped. However, friction of some sort usually dampens the motion, so it fades away or needs more force to continue. For example, a guitar string stops oscillating a few seconds after being plucked. Similarly, one must continually push a swing to keep a child swinging on a playground.
Although friction and other non-conservative...
Full wave rectifier01:22

Full wave rectifier

A full-wave rectifier is a device that converts alternating current (AC) to direct current (DC) and is more efficient than its half-wave counterpart. It typically includes a center-tapped transformer, two diodes, and a load resistor. The secondary winding of the transformer is divided to provide two equal voltages of opposite polarities, which is the pivotal element of full-wave rectification.