Related Experiment Video

Updated: Jul 20, 2026

Low-Cost Cryo-Light Microscopy Stage Fabrication for Correlated Light/Electron Microscopy
10:00

Low-Cost Cryo-Light Microscopy Stage Fabrication for Correlated Light/Electron Microscopy

Published on: June 5, 2011

The preparation and structures of hydrogen ordered phases of ice

Christoph G Salzmann1, Paolo G Radaelli, Andreas Hallbrucker

  • 1Institute of General, Inorganic, and Theoretical Chemistry, University of Innsbruck, Innrain 52a, 6020 Innsbruck, Austria. christoph.salzmann@chemistry.oxford.ac.uk

Science (New York, N.Y.)
|March 25, 2006
PubMed

More Related Videos

Determining the Ice-binding Planes of Antifreeze Proteins by Fluorescence-based Ice Plane Affinity08:46

Determining the Ice-binding Planes of Antifreeze Proteins by Fluorescence-based Ice Plane Affinity

Published on: January 15, 2014

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine08:16

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine

Published on: March 13, 2017

Related Concept Videos

States of Water01:23

States of Water

Water exists in any one of the three classical states: solid (ice), liquid (water), and gas (steam or water vapor). The state of water depends on i) the intermolecular forces that draw molecules together and ii) the kinetic energy that leads to movements that pull them apart.
Water freezes when the intermolecular forces are greater than the kinetic energy. Unlike most other substances, water is less dense in its solid state than in its liquid state. This is because each water molecule can form...
Mass Concreting01:22

Mass Concreting

Mass concreting refers to the process of placing large volumes of concrete, such as in gravity dams. The heat generated during the cement hydration process and differential cooling rates within the concrete mass can lead to a temperature gradient, which can result in thermal cracks in the concrete mass.
To reduce the risk of such cracking, the concrete mix may incorporate low-heat cement and pozzolans to reduce the temperature rise. Pre-cooled angular aggregates and water-reducing admixtures...
Cold Weather Concreting01:27

Cold Weather Concreting

When freshly poured concrete is exposed to freezing temperatures before it has set, the water within the concrete can freeze. This expansion disrupts the setting process, delays chemical reactions necessary for hardening, and increases the volume of pores within the hardened concrete, which weakens its overall structure. If the concrete manages to reach an appreciable strength before it freezes, the damage can be somewhat mitigated.
To counteract the negative impacts of cold weather, ensuring...
Frost Action on Concrete01:27

Frost Action on Concrete

Concrete structures in cold climates, such as those along roadsides, can retain moisture. This moisture makes them susceptible to frost-related damage when temperatures fall below freezing. Adding moisture worsens the damage during temperature fluctuations, leading to repeated freezing and thawing. De-icing salts, spread over these structures to melt ice, add to the freeze-thaw cycle, and draw even more moisture into the concrete.
This freeze-thaw cycle primarily causes surface scaling, where...
Frost Resistant Concrete01:29

Frost Resistant Concrete

Concrete's susceptibility to frost damage during freeze-thaw cycles demands strategic measures to enhance its frost resistance. Employing techniques like air entrainment, adjusting the water-cement ratio, proper curing, and selecting appropriate aggregates are essential.
Introducing microscopic air bubbles into the concrete mix through air entrainment creates small voids that accommodate ice expansion, thereby reducing internal pressures and preventing cracking. The optimal amount of entrained...
Structural Steel Products01:24

Structural Steel Products

Structural steel products are created within a structural mill. The process begins with a beam blank that is reheated and then fed through a series of rollers. These rollers progressively shape the metal into its final form. Adjusting the spacings between the rollers allows for the production of different sections with the same nominal dimensions.
Once shaped, the steel's final form emerges as a continuous length, which is then segmented by a hot saw into manageable pieces. These segments are...