Related Experiment Video

Updated: Jan 23, 2026

Symptom Assessment of Patients with Allergic Rhinitis Using an Allergen Exposure Chamber
08:47

Symptom Assessment of Patients with Allergic Rhinitis Using an Allergen Exposure Chamber

Published on: March 3, 2023

2.9K

Patch-testing with plastics and glues series allergens

Eugenia Shmidt1, Sara A Farmer, Mark D P Davis

  • 1Department of Dermatology and the Division of Biomedical Informatics and Biostatistics, Mayo Clinic, Rochester, MN, USA.

Dermatitis : Contact, Atopic, Occupational, Drug
|October 6, 2010
PubMed
Abstract

More Related Videos

Humanized Mediator Release Assay as a Read-Out for Allergen Potency10:22

Humanized Mediator Release Assay as a Read-Out for Allergen Potency

Published on: June 29, 2021

3.9K
Slice Patch Clamp Technique for Analyzing Learning-Induced Plasticity11:56

Slice Patch Clamp Technique for Analyzing Learning-Induced Plasticity

Published on: November 11, 2017

16.3K

Related Concept Videos

Plasticizers01:31

Plasticizers

Water-reducers, or plasticizers, are chemical admixtures used in concrete to improve strength and workability. These additives reduce the water-cement ratio without compromising workability, lower the cement content while maintaining the same workability, or increase workability to assist concrete placement in inaccessible areas.
Plasticizers function by using surface-active agents to create repulsive electrostatic forces between cement particles. This dispersion enhances the concrete's...
352
Plasticity00:58

Plasticity

Plasticity is the property where an object loses its elasticity and undergoes irreversible deformation, even after the deformation forces are eliminated. If a material deforms irreversibly without increasing stress or load, then this is called ideal plasticity. For example, when a force is applied to an aluminum rod, it changes its shape, but it does not return to its original shape once the force is removed. Plastic deformation or ductility is thus a permanent deformation or change in the...
3.0K
Resistors In Series01:10

Resistors In Series

A resistor is an ohmic device that limits the flow of charge in a circuit. Most circuits have more than one resistor. If several resistors are connected together and connected to a battery, the current supplied by the battery depends on the equivalent resistance of the circuit. The equivalent resistance of a combination of resistors depends on both their individual values and how they are connected. The simplest combination of resistors is the series combination. 
In a series circuit, the...
6.1K
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
531
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
412
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
439