Related Experiment Video

Updated: Jun 4, 2026

Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator
07:42

Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator

Published on: December 15, 2021

Properties of SAW synchronous two-port resonators on GdCa₄O(BO₃)₃ crystal

Waldemar Soluch1

  • 1Institute of Electronic Materials Technology, Warsaw, Poland. waldemar.soluch@itme.edu.pl

IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
|February 24, 2011
PubMed

More Related Videos

Fabrication and Characterization of Superconducting Resonators10:26

Fabrication and Characterization of Superconducting Resonators

Published on: May 21, 2016

Fabrication and Characterization of High-Q Silicon Nitride Membrane Resonators09:46

Fabrication and Characterization of High-Q Silicon Nitride Membrane Resonators

Published on: August 8, 2025

Related Concept Videos

Characteristics of Series Resonant Circuit01:24

Characteristics of Series Resonant Circuit

Series resonance occurs in a circuit containing inductive (L), capacitive (C), and resistive (R) elements connected sequentially. At the resonance frequency, the inductive and capacitive reactances are equal in magnitude but opposite in sign, effectively canceling each other. This causes the circuit's impedance is minimal, primarily determined by the resistance R. The resonant frequency of an RLC circuit is defined as:
Double Resonance Techniques: Overview01:12

Double Resonance Techniques: Overview

Double resonance techniques in Nuclear Magnetic Resonance (NMR) spectroscopy involve the simultaneous application of two different frequencies or radiofrequency pulses to manipulate and observe two distinct nuclear spins. One important application of double resonance is spin decoupling, which selectively suppresses coupling with one type of nucleus while observing the NMR signal from another nucleus, simplifying the spectrum and enhancing resolution.
Spin decoupling is usually achieved by...
Parallel Resonance01:23

Parallel Resonance

The parallel RLC circuit is an arrangement where the resistor (R), inductor (L), and capacitor (C) are all connected to the same nodes and, as a result, share the same voltage across them. The parallel RLC circuit is analyzed in terms of admittance (Y), which reflects the ease with which current can flow. The admittance is given by:
Resonance in an AC Circuit01:26

Resonance in an AC Circuit

The property of an inductor makes it resist any change in the current passing through it, while the property of a capacitor is to build up the charge across its terminals. Hence, if an inductor and capacitor are connected in series, they have opposite effects on the relative phase between current and voltage. The current through the circuit undergoes forced oscillation at the frequency of the source. The resistance term in an R-L-C circuit acts as a damping term because power is dissipated...
Concept of Resonance and its Characteristics01:19

Concept of Resonance and its Characteristics

If a driven oscillator needs to resonate at a specific frequency, then very light damping is required. An example of light damping includes playing piano strings and many other musical instruments. Conversely, to achieve small-amplitude oscillations as in a car's suspension system, heavy damping is required. Heavy damping reduces the amplitude, but the tradeoff is that the system responds at more frequencies. Speed bumps and gravel roads prove that even a car's suspension system is not immune...
Design Example: Underdamped Parallel RLC Circuit01:17

Design Example: Underdamped Parallel RLC Circuit

Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
Starting with a fixed...