Related Experiment Video

Updated: May 14, 2026

Preparation of Polyoxometalate-based Photo-responsive Membranes for the Photo-activation of Manganese Oxide Catalysts
05:47

Preparation of Polyoxometalate-based Photo-responsive Membranes for the Photo-activation of Manganese Oxide Catalysts

Published on: August 7, 2018

Photoinduced charge transfer involving a MoMo quadruply bonded complex to a perylene diimide

Brian G Alberding1, Samantha E Brown-Xu, Malcolm H Chisholm

  • 1The Ohio State University, 100 West 18th Avenue, Columbus, OH 43210, USA.

Dalton Transactions (Cambridge, England : 2003)
|February 16, 2013
PubMed

More Related Videos

Integrating a Triplet-triplet Annihilation Up-conversion System to Enhance Dye-sensitized Solar Cell Response to Sub-bandgap Light11:26

Integrating a Triplet-triplet Annihilation Up-conversion System to Enhance Dye-sensitized Solar Cell Response to Sub-bandgap Light

Published on: September 12, 2014

Developing Photosensitizer-Cobaloxime Hybrids for Solar-Driven H2 Production in Aqueous Aerobic Conditions10:21

Developing Photosensitizer-Cobaloxime Hybrids for Solar-Driven H2 Production in Aqueous Aerobic Conditions

Published on: October 5, 2019

Related Concept Videos

Photochemical Electrocyclic Reactions: Stereochemistry01:26

Photochemical Electrocyclic Reactions: Stereochemistry

The absorption of UV–visible light by conjugated systems causes the promotion of an electron from the ground state to the excited state. Consequently, photochemical electrocyclic reactions proceed via the excited-state HOMO rather than the ground-state HOMO. Since the ground- and excited-state HOMOs have different symmetries, the stereochemical outcome of electrocyclic reactions depends on the mode of activation; i.e., thermal or photochemical.
Selection Rules: Photochemical Activation
Cycloaddition Reactions: MO Requirements for Photochemical Activation01:12

Cycloaddition Reactions: MO Requirements for Photochemical Activation

Some cycloaddition reactions are activated by heat, while others are initiated by light. For example, a [2 + 2] cycloaddition between two ethylene molecules occurs only in the presence of light. It is photochemically allowed but thermally forbidden.
Thermal and Photochemical Electrocyclic Reactions: Overview01:26

Thermal and Photochemical Electrocyclic Reactions: Overview

Electrocyclic reactions are reversible reactions. They involve an intramolecular cyclization or ring-opening of a conjugated polyene. Shown below are two examples of electrocyclic reactions. In the first reaction, the formation of the cyclic product is favored. In contrast, in the second reaction, ring-opening is favored due to the high ring strain associated with cyclobutene formation.
[3,3] Sigmatropic Rearrangement of 1,5-Dienes: Cope Rearrangement01:21

[3,3] Sigmatropic Rearrangement of 1,5-Dienes: Cope Rearrangement

The Cope rearrangement is classified as a [3,3] sigmatropic shift in 1,5-dienes, leading to a more stable, isomeric 1,5-diene. The reaction involves a concerted movement of six electrons, four from two π bonds and two from a σ bond, via an energetically favorable chair-like transition state.
Photosystem I01:27

Photosystem I

Although structurally similar to photosystem II (PSII), photosystem I (PSI) is has a different electron supplier and electron acceptor.
Both these photosystems work in concert. An excited electron from PSII is relayed to PSI via an electron transport chain in the thylakoid membrane of the chloroplast, which is comprised of the carrier molecule plastoquinone, the dual-protein cytochrome complex, and plastocyanin. As electrons move between PSII and PSI, they lose energy and must be re-energized...
¹H NMR: Complex Splitting01:13

¹H NMR: Complex Splitting

A proton M that is coupled to a proton X results in doublet signals for M. However, NMR-active nuclei can be simultaneously coupled to more than one nonequivalent nucleus. When M is coupled to a second proton A, such as in styrene oxide, each peak in the doublet is split into another doublet.
Splitting diagrams or splitting tree diagrams are routinely used to depict such complex couplings. While drawing splitting diagrams, the splitting with the larger coupling constant is usually applied first.