Related Experiment Video

Updated: May 3, 2026

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes
06:34

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes

Published on: January 6, 2023

2.8K

Collapse pressure analysis of transversely isotropic thick-walled cylinder using Lebesgue strain measure and

A K Aggarwal1, Richa Sharma1, Sanjeev Sharma1

  • 1Department of Mathematics, Jaypee Institute of Information Technology, A-10, Sector 62, Noida 201307, India.

Thescientificworldjournal
|February 14, 2014
PubMed

More Related Videos

Biaxial Basal Tone and Passive Testing of the Murine Reproductive System Using a Pressure Myograph09:59

Biaxial Basal Tone and Passive Testing of the Murine Reproductive System Using a Pressure Myograph

Published on: August 13, 2019

8.7K
Ultrasonic Fatigue Testing in the Tension-Compression Mode06:54

Ultrasonic Fatigue Testing in the Tension-Compression Mode

Published on: March 7, 2018

10.1K

Related Concept Videos

Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
604
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
740
Bending of Curved Members - Strain Analysis01:14

Bending of Curved Members - Strain Analysis

The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
The important part of bending analysis for such a member...
678
Castigliano's Theorem01:18

Castigliano's Theorem

Castigliano's theorem analyzes displacements and rotations in elastic structures. It relates the derivative of elastic strain energy to the applied forces or moments, allowing for the calculation of deformations. The theorem states that the partial derivative of the total strain energy of a system with respect to a specific load results in the displacement at the point where the load is applied. This principle applies to both forces and moments.
1.4K
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
681
Transformation of Plane Strain01:12

Transformation of Plane Strain

When analyzing elongated structures like bars subjected to uniformly distributed loads, it is essential to understand the transformation of plane strain when coordinate axes are rotated. This transformation helps to assess how material deformation characteristics vary with orientation, which is crucial in materials science and structural engineering.
Under plane strain conditions, typical for members where one dimension significantly exceeds the others, deformations and resultant strains are...
673