Related Experiment Video

Updated: Apr 27, 2026

Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator
06:45

Design and Application of a Fault Detection Method Based on Adaptive Filters and Rotational Speed Estimation for an Electro-Hydrostatic Actuator

Published on: October 28, 2022

1.7K

A stochastic framework for robust fuzzy filtering and analysis of signals--part II

Mohit Kumar, Norbert Stoll, Regina Stoll

    IEEE Transactions on Cybernetics
    |June 25, 2014
    PubMed

    More Related Videos

    Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles11:54

    Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles

    Published on: March 13, 2017

    8.7K
    Real-Time Proxy-Control of Re-Parameterized Peripheral Signals using a Close-Loop Interface11:54

    Real-Time Proxy-Control of Re-Parameterized Peripheral Signals using a Close-Loop Interface

    Published on: May 8, 2021

    4.2K

    Related Concept Videos

    State Space Representation01:27

    State Space Representation

    The frequency-domain technique, commonly used in analyzing and designing feedback control systems, is effective for linear, time-invariant systems. However, it falls short when dealing with nonlinear, time-varying, and multiple-input multiple-output systems. The time-domain or state-space approach addresses these limitations by utilizing state variables to construct simultaneous, first-order differential equations, known as state equations, for an nth-order system.
    Consider an RLC circuit, a...
    782
    Sampling Continuous Time Signal01:11

    Sampling Continuous Time Signal

    In signal processing, a continuous-time signal can be sampled using an impulse-train sampling technique, followed by the zero-order hold method. Impulse-train sampling involves the use of a periodic impulse train, which consists of a series of delta functions spaced at regular intervals determined by the sampling period. When a continuous-time signal is multiplied by this impulse train, it generates impulses with amplitudes corresponding to the signal's values at the sampling points.
    In the...
    917
    Basic Continuous Time Signals01:22

    Basic Continuous Time Signals

    Basic continuous-time signals include the unit step function, unit impulse function, and unit ramp function, collectively referred to as singularity functions. Singularity functions are characterized by discontinuities or discontinuous derivatives.
    The unit step function, denoted u(t), is zero for negative time values and one for positive time values, exhibiting a discontinuity at t=0. This function often represents abrupt changes, such as the step voltage introduced when turning a car's...
    883
    Propagation of Uncertainty from Random Error00:59

    Propagation of Uncertainty from Random Error

    An experiment often consists of more than a single step. In this case, measurements at each step give rise to uncertainty. Because the measurements occur in successive steps, the uncertainty in one step necessarily contributes to that in the subsequent step. As we perform statistical analysis on these types of experiments, we must learn to account for the propagation of uncertainty from one step to the next. The propagation of uncertainty depends on the type of arithmetic operation performed on...
    1.9K
    Propagation of Uncertainty from Systematic Error01:10

    Propagation of Uncertainty from Systematic Error

    The atomic mass of an element varies due to the relative ratio of its isotopes. A sample's relative proportion of oxygen isotopes influences its average atomic mass. For instance, if we were to measure the atomic mass of oxygen from a sample, the mass would be a weighted average of the isotopic masses of oxygen in that sample. Since a single sample is not likely to perfectly reflect the true atomic mass of oxygen for all the molecules of oxygen on Earth, the mass we obtain from this...
    1.4K
    Classification of Signals01:30

    Classification of Signals

    In signal processing, signals are classified based on various characteristics: continuous-time versus discrete-time, periodic versus aperiodic, analog versus digital, and causal versus noncausal. Each category highlights distinct properties crucial for understanding and manipulating signals.
    A continuous-time signal holds a value at every instant in time, representing information seamlessly. In contrast, a discrete-time signal holds values only at specific moments, often denoted as x(n), where...
    1.5K