Related Experiment Video

Updated: Apr 3, 2026

Measuring Biophysical and Psychological Stress Levels Following Visitation to Three Locations with Differing Levels of Nature
05:33

Measuring Biophysical and Psychological Stress Levels Following Visitation to Three Locations with Differing Levels of Nature

Published on: June 19, 2019

9.1K

Determinants of job stress in chemical process industry: A factor analysis approach

Balagopal G Menon1,2, C J Praveensal2,3, G Madhu3

  • 1Department of Industrial Engineering and Management, Indian Institute of Technology, Kharagpur, West Bengal, India.

Work (Reading, Mass.)
|September 28, 2015
PubMed
Abstract

Keywords:
Role ambiguityphysical work factorsrole conflictstructural equation modelingworking environment

More Related Videos

Evaluation of Commercial-Off-The-Shelf Wrist Wearables to Estimate Stress on Students12:51

Evaluation of Commercial-Off-The-Shelf Wrist Wearables to Estimate Stress on Students

Published on: June 16, 2018

8.0K
A Cost-effective and Reliable Method to Predict Mechanical Stress in Single-use and Standard Pumps07:34

A Cost-effective and Reliable Method to Predict Mechanical Stress in Single-use and Standard Pumps

Published on: August 5, 2015

9.9K

Related Concept Videos

Factors Affecting Workability01:24

Factors Affecting Workability

The workability of concrete is a critical characteristic that influences the ease of mixing, handling, and finishing the concrete. It is affected by several factors including water content, aggregate properties, and admixtures like air entrainment. Water plays a fundamental role as it lubricates the concrete mix, facilitating easier movement and placement. However, the water requirement varies depending on the texture and shape of aggregates. Finer particles and angular, rough-textured...
358
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress...
777
Stress Concentrations01:24

Stress Concentrations

Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller...
820
Introduction to Stress and Lifestyle01:27

Introduction to Stress and Lifestyle

Stress is a multifaceted response to events perceived as challenging or threatening, highlighting physical, emotional, cognitive, and behavioral reactions. Physically, stress can lead to fatigue, sleep disruptions, and various health issues such as frequent colds, chest pains, and nausea. Emotionally, it can manifest as anxiety, depression, irritability, and anger triggered by both minor and major life events. Cognitively, it may result in difficulty in concentration, memory, and...
814
Le Chatelier's Principle: Changing Concentration02:27

Le Chatelier's Principle: Changing Concentration

A system at equilibrium is in a state of dynamic balance, with forward and reverse reactions taking place at equal rates. If an equilibrium system is subjected to a change in conditions that affects these reaction rates differently (a stress), then the rates are no longer equal and the system is not at equilibrium. The system will subsequently experience a net reaction in the direction of a greater rate (a shift) that will re-establish the equilibrium. This phenomenon is summarized by Le...
69.1K
Stress: General Loading Conditions01:15

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes....
685