Related Experiment Video

Updated: Mar 22, 2026

The Measurement of Unsteady Surface Pressure Using a Remote Microphone Probe
08:53

The Measurement of Unsteady Surface Pressure Using a Remote Microphone Probe

Published on: December 3, 2016

7.4K

Effect of Power Line Interference on Microphone Calibration Measurements Made at or Near Harmonics of the Power Line

Randall P Wagner1, Victor Nedzelnitsky1

  • 1National Institute of Standards and Technology, Gaithersburg, MD 20899-8220.

Journal of Research of the National Institute of Standards and Technology
|April 26, 2016
PubMed

Keywords:
acoustic calibrationsacoustic measurementscalibrationelectronic instrumentationmicrophone calibrationmicrophone pressure calibrationmicrophone reciprocity calibrationpower line frequencypower line interferencepressure reciprocity calibration of microphones

More Related Videos

Calibration of Vector Network Analyzer for Measurements in Radio Frequency Propagation Channels10:00

Calibration of Vector Network Analyzer for Measurements in Radio Frequency Propagation Channels

Published on: June 2, 2020

23.0K
X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells10:16

X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells

Published on: August 20, 2019

14.5K

Related Concept Videos

Interference: Path Lengths01:10

Interference: Path Lengths

Consider two sources of sound, that may or may not be in phase, emitting waves at a single frequency, and consider the frequencies to be the same.
Two special sources may be considered when they are in phase. This can be easily achieved by feeding the two sources from the same source. An example would be synchronizing the two speakers by feeding them with the same source, such as the sound waves produced by a tuning fork. This setup ensures that the two sources have the same frequency and are...
2.4K
Sound Waves: Interference00:53

Sound Waves: Interference

Sound waves can be modeled either as longitudinal waves, wherein the molecules of the medium oscillate around an equilibrium position, or as pressure waves. When two identical waves from the same source superimpose on each other, the combination of two crests or two troughs results in amplitude reinforcement known as constructive interference. If two identical waves, that are initially in phase, become out of phase because of different path lengths, the combination of crests with troughs...
5.1K
Applications of EMF Measurements01:26

Applications of EMF Measurements

Electromotive force (EMF) measurements have a broad range of applications in various fields, including chemistry and physics. The electrochemical series, an arrangement of elements in order of their standard electrode potentials, can be determined through EMF measurements. Elements with lower standard potentials can reduce ions of elements with higher standard potentials.The standard cell potential, E°, allows for the calculation of the standard reaction Gibbs energy, ΔG°, and...
39
Parallel Resonance01:23

Parallel Resonance

The parallel RLC circuit is an arrangement where the resistor (R), inductor (L), and capacitor (C) are all connected to the same nodes and, as a result, share the same voltage across them. The parallel RLC circuit is analyzed in terms of admittance (Y), which reflects the ease with which current can flow. The admittance is given by:
720
Resonance in an AC Circuit01:26

Resonance in an AC Circuit

The property of an inductor makes it resist any change in the current passing through it, while the property of a capacitor is to build up the charge across its terminals. Hence, if an inductor and capacitor are connected in series, they have opposite effects on the relative phase between current and voltage. The current through the circuit undergoes forced oscillation at the frequency of the source. The resistance term in an R-L-C circuit acts as a damping term because power is dissipated...
2.7K
Power Factor Correction01:20

Power Factor Correction

The power transmission to a factory involves the transfer of apparent power, a combination of active and reactive power. The power factor measures how effectively electrical power is converted into useful work output. The ratio of the real power (KW) that does the work to the apparent power (KVA) supplied to the circuit.
660