Related Experiment Video

Updated: Mar 15, 2026

Application of Design Aspects in Uniaxial Loading Machine Development
05:23

Application of Design Aspects in Uniaxial Loading Machine Development

Published on: September 19, 2018

6.4K

An electromyographic and kinematic comparison between an extendable conveyor system and an articulating belt conveyor

Steven A Lavender1, Shasank Nagavarapu2, W Gary Allread3

  • 1Integrated Systems Engineering, The Ohio State University, United States; Orthopaedics, The Ohio State University, United States; Institute for Ergonomics, The Ohio State University, United States.

Applied Ergonomics
|September 17, 2016
PubMed

Keywords:
Conveyor systemsDistribution centersMusculoskeletal disorders

More Related Videos

Simulation of a Scaled Assembly Process with Collaboration of a Robotic Arm and Monitoring through a Vision System for Quality Control05:47

Simulation of a Scaled Assembly Process with Collaboration of a Robotic Arm and Monitoring through a Vision System for Quality Control

Published on: August 29, 2025

527
Author Spotlight: Introduction to Active Probe Atomic Force Microscopy with Quattro-Parallel Cantilever Arrays05:04

Author Spotlight: Introduction to Active Probe Atomic Force Microscopy with Quattro-Parallel Cantilever Arrays

Published on: June 13, 2023

2.5K

Related Concept Videos

Machines: Problem Solving II01:30

Machines: Problem Solving II

Machines are complex structures consisting of movable, pin-connected multi-force members that work together to transmit forces. Consider a lifting tong carrying a 100 kg load. It comprises movable sections DAF and CBG linked together with member AB.
725
Frictional Forces on Flat Belts01:28

Frictional Forces on Flat Belts

Flat belts are commonly used in various industrial applications for transmitting power from one pulley to another. When a flat belt is wrapped around a set of pulleys, it experiences different tensions at the driving pulley ends due to the friction between the belt and pulley surface. When the pulley moves in a counterclockwise direction, the tension T2 on the opposite side of the pulley where the belt is moving away from is higher than the tension T1 on the side where the belt is moving...
1.6K
Frames: Problem Solving I01:24

Frames: Problem Solving I

Consider a jib crane with an external load suspended from the pulley. The dimensions of the crane members are shown in the figure. A systematic analysis of the frame structure is required to determine the reaction forces at the pin joints, assuming that the pulleys are frictionless.
1.1K
Flat Belts: Problem Solving01:28

Flat Belts: Problem Solving

Flat belts are crucial in many industrial applications as they help transmit power from one pulley to another. The concept of forces and moments is used to determine the maximum moment on a pulley. For instance, consider a flat belt that wraps around two pulleys, A and B, with radii of 30 cm and 10 cm, respectively. The angle between the belt and the horizontal is 20 degrees at the pulleys. As pulley B rotates clockwise and drives pulley A, tension T2 is caused at one end of the belt, while...
915
Impact Loading on a Cantilever Beam01:13

Impact Loading on a Cantilever Beam

The analysis of a cantilever beam with a circular cross-section subjected to impact loading at its free end illustrates the conversion of potential energy from a dropped object into kinetic energy, which is then absorbed by the beam as strain energy. This process is crucial for understanding how materials behave under dynamic loads, which is important in fields such as construction and aerospace.
When an object is dropped onto the free end of a cantilever, its potential energy due to gravity is...
972
Cable Subjected to Concentrated Loads01:28

Cable Subjected to Concentrated Loads

Flexible cables are commonly used in various applications for support and load transmission. Consider a cable fixed at two points and subjected to multiple vertically concentrated loads. Determine the shape of the cable and the tension in each portion of the cable, given the horizontal distances between the loads and supports.
1.5K