Thoracogenic spinal deformity: a rare cause of early-onset scoliosis

Sarah F Eby1, Tricia St Hilaire2, Michael Glotzbecker3

  • 11Mayo Medical School, Mayo Graduate School, and the Medical Scientist Training Program, College of Medicine, Mayo Clinic, Rochester, Minnesota.

Insights

Severe scoliosis can develop in infants after thoracoabdominal surgery. This study found thoracogenic scoliosis in 1.6% of patients, with surgical treatment showing improvement but also complications.

Area of Science:

  • Pediatric Surgery
  • Orthopedic Surgery
  • Spine Deformity

Background:

  • Thoracoabdominal surgery for congenital defects is life-saving but may lead to scoliosis.
  • The incidence of post-surgical scoliosis ranges from 8% to 50%, with limited data on infant chest wall procedures.

Purpose of the Study:

  • To determine the prevalence of thoracogenic scoliosis.
  • To assess disease severity and the need for surgical intervention in infants undergoing chest wall procedures.

Main Methods:

  • A multicenter database of early-onset scoliosis patients was queried.
  • Patients with congenital spine deformities were excluded; 41 with thoracogenic scoliosis were identified.
  • Treatment outcomes (observation, bracing, surgery) and complications were reviewed.

Main Results:

  • Thoracogenic scoliosis was identified in 41 patients (1.6%).
  • Surgical treatment in 17 patients improved the mean Cobb angle from 65° to 47° (p=0.01).
  • Nonoperative management showed no significant change (31° to 32°, p=0.44), with no complications.

Conclusions:

  • Severe scoliosis is a potential outcome of infant thoracoabdominal surgery.
  • Further research is needed to understand scoliosis pathogenesis for prevention and early diagnosis.
  • Appropriate treatment strategies for this population require further investigation.

Related Concept Videos

Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
470
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
455
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
407
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
521
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
479
Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
924