Related Experiment Video

Updated: Feb 4, 2026

Automated Deployment of an Internet Protocol Telephony Service on Unmanned Aerial Vehicles Using Network Functions Virtualization
07:49

Automated Deployment of an Internet Protocol Telephony Service on Unmanned Aerial Vehicles Using Network Functions Virtualization

Published on: November 26, 2019

8.5K

Design of Amphibious Vehicle for Unmanned Mission in Water Quality Monitoring Using Internet of Things

Balasubramanian Esakki1, Surendar Ganesan2, Silambarasan Mathiyazhagan3

  • 1Centre for Autonomous System Research, VelTech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology, Avadi, Chennai 600 062, India. balasubramaniane@veltech.edu.in.

Sensors (Basel, Switzerland)
|October 5, 2018
PubMed

Keywords:
CFDFEAInternet of Thingsamphibious UAVhovercraftprototypesensorswater quality

More Related Videos

Continuous Hydrologic and Water Quality Monitoring of Vernal Ponds06:37

Continuous Hydrologic and Water Quality Monitoring of Vernal Ponds

Published on: November 13, 2017

9.7K
Structural Design and Manufacturing of a Cruiser Class Solar Vehicle14:57

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle

Published on: January 30, 2019

14.4K

Related Concept Videos

Quality of Water01:19

Quality of Water

In concrete preparation, the quality of water is paramount as it affects the strength and durability of the concrete. Potable water is usually preferred; however, it must not have excessive sodium or potassium to prevent compromising the concrete's integrity. Water quality is typically evaluated based on impurities such as dissolved solids, chlorides, and sulfates, and its pH value is ideally between 6 and 8. Even slightly acidic natural water may be acceptable unless it contains harmful...
568
Testing Water Quality01:14

Testing Water Quality

When the quality of water for concrete preparation is uncertain, its impact on the setting time of cement and compressive strength of mortar is assessed by comparison with de-ionized or distilled water benchmarks. American Society for Testing and Materials (ASTM) C1602 requires the setting times to be within 90 minutes of the control, British Standard (BS) 3146:1980 allows a 30-minute variance in the initial setting, while British Standards European Norm (BS EN) 1008 specifies initial setting...
391
Design Example: Designing Water Slide01:18

Design Example: Designing Water Slide

When designing a water slide, controlling the speed of water flow is crucial for rider safety while maintaining an exciting experience. As water flows down the slide, gravity causes it to accelerate, with its speed at the bottom depending on the height from which it starts. The higher the slide, the more potential energy the water has at the top, which is converted into kinetic energy as it descends, increasing its speed.
Bernoulli's principle determines the water's velocity along the slide....
630
Group Design02:01

Group Design

The most basic experimental design involves two groups: the experimental group and the control group. The two groups are designed to be the same except for one difference— experimental manipulation. The experimental group gets the experimental manipulation—that is, the treatment or variable being tested—and the control group does not. Since experimental manipulation is the only difference between the experimental and control groups, we can be sure that any differences between...
10.5K
States of Water01:23

States of Water

Water exists in any one of the three classical states: solid (ice), liquid (water), and gas (steam or water vapor). The state of water depends on i) the intermolecular forces that draw molecules together and ii) the kinetic energy that leads to movements that pull them apart.
Water freezes when the intermolecular forces are greater than the kinetic energy. Unlike most other substances, water is less dense in its solid state than in its liquid state. This is because each water molecule can form...
57.0K
Quality Control01:05

Quality Control

Quality control is one of the three cyclical quality assurance activities that help keep a system under statistical control. Typical quality control activities include creating quality control charts, conducting proficiency testing, and documenting and archiving results.
Quality control helps track data, visualize trends, and identify variations, making it easier to detect deviations that may affect the accuracy of an analysis. One way to do this is by generating a quality control chart, which...
2.6K