Related Experiment Video

Updated: Jan 28, 2026

Designing CAD/CAM Surgical Guides for Maxillary Reconstruction Using an In-house Approach
08:01

Designing CAD/CAM Surgical Guides for Maxillary Reconstruction Using an In-house Approach

Published on: August 24, 2018

9.4K

Novel Plate Design to Improve Mandibular and Maxillary Reconstruction with the Osteocutaneous Fibula Flap

Miller H Smith1, Christiaan H Schrag2, Shamir P Chandarana3

  • 1Section of Oral Surgery, Department of Surgery, University of Calgary, Calgary, AB, Canada.

Plastic and Reconstructive Surgery. Global Open
|March 13, 2019
PubMed

More Related Videos

Coronoid-Temporalis Pedicled Flap for Orbital Floor Defect Reconstruction06:32

Coronoid-Temporalis Pedicled Flap for Orbital Floor Defect Reconstruction

Published on: December 5, 2025

646
The Superficial Inferior Epigastric Artery Fascia Flap for Nerve Reconstruction in Rabbits12:01

The Superficial Inferior Epigastric Artery Fascia Flap for Nerve Reconstruction in Rabbits

Published on: June 13, 2025

922

Related Concept Videos

Bones of the Lower Limb: Tibia and Fibula01:10

Bones of the Lower Limb: Tibia and Fibula

The tibia is the main weight-bearing bone of the lower leg. It is larger than the fibula with which it is paired. The tibia is also the second longest bone in the body and is located right below the skin. The proximal end of the tibia forms the medial and the lateral condyle, which articulates with the condyles of the femur to form the knee joint. Between the articulating surfaces is the irregular elevated area known as the intercondylar eminence that serves as the inferior attachment point for...
9.2K
Group Design02:01

Group Design

The most basic experimental design involves two groups: the experimental group and the control group. The two groups are designed to be the same except for one difference— experimental manipulation. The experimental group gets the experimental manipulation—that is, the treatment or variable being tested—and the control group does not. Since experimental manipulation is the only difference between the experimental and control groups, we can be sure that any differences between...
10.4K
Factorial Design02:01

Factorial Design

Factorial Analysis is an experimental design that applies Analysis of Variance (ANOVA) statistical procedures to examine a change in a dependent variable due to more than one independent variable, also known as factors. Changes in worker productivity can be reasoned, for example, to be influenced by salary and other conditions, such as skill level. One way to test this hypothesis is by categorizing salary into three levels (low, moderate, and high) and skills sets into two levels (entry level...
13.8K
Design Example: Designing a Residential Plumbing System01:25

Design Example: Designing a Residential Plumbing System

The design of residential plumbing systems requires carefully evaluating water demand, flow rates, and pressure dynamics to ensure both efficiency and reliability. The nature of water flow within pipes is defined by its Reynolds number, which classifies flow as either laminar (smooth) or turbulent.
1.1K
Design Example: Designing Water Slide01:18

Design Example: Designing Water Slide

When designing a water slide, controlling the speed of water flow is crucial for rider safety while maintaining an exciting experience. As water flows down the slide, gravity causes it to accelerate, with its speed at the bottom depending on the height from which it starts. The higher the slide, the more potential energy the water has at the top, which is converted into kinetic energy as it descends, increasing its speed.
Bernoulli's principle determines the water's velocity along the slide....
624
Design Example: Design of an Irrigation Channel01:27

Design Example: Design of an Irrigation Channel

Trapezoidal channels are widely used in irrigation systems due to their cost-effectiveness and efficiency in conveying water. Trapezoidal channels feature a flat bottom and sloping sides, making them stable and easier to construct compared to other shapes. The bottom width and side slope ratio are determined based on the required flow capacity and site conditions. The side slope is kept gentle for unlined channels to prevent soil erosion.Hydraulic parameters in channel design include the flow...
823