Related Experiment Video

Updated: Jan 25, 2026

Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats & Spheres
13:07

Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats & Spheres

Published on: December 1, 2014

11.6K

Research on High Precision and Deterministic Figuring for Shaft Parts Based on Abrasive Belt Polishing

Xuelei Chen1, Yifan Dai2, Hao Hu3

  • 1College of Artificial Intelligence and Automation, National University of Defense Technology, 109 Deya Road, Changsha 410073, Hunan, China. 15954898151@163.com.

Materials (Basel, Switzerland)
|May 1, 2019
PubMed

Keywords:
abrasive beltdeterministicfiguringpolishingroundness errorshaft parts

More Related Videos

An Epithelial Abrasion Model for Studying Corneal Wound Healing04:45

An Epithelial Abrasion Model for Studying Corneal Wound Healing

Published on: December 29, 2021

3.8K
Experimental Protocol to Investigate Particle Aerosolization of a Product Under Abrasion and Under Environmental Weathering07:47

Experimental Protocol to Investigate Particle Aerosolization of a Product Under Abrasion and Under Environmental Weathering

Published on: September 16, 2016

7.8K

Related Concept Videos

Uncertainty in Measurement: Significant Figures03:34

Uncertainty in Measurement: Significant Figures

All the digits in a measurement, including the uncertain last digit, are called significant figures or significant digits. Note that zero may be a measured value; for example, if a scale that shows weight to the nearest pound reads “140,” then the 1 (hundreds), 4 (tens), and 0 (ones) are all significant (measured) values.
81.0K
Rules for Significant Figures01:44

Rules for Significant Figures

In any measurement, the precision of the measuring tool is an essential factor. An ordinary ruler, for example, can measure length to the closest millimeter; a caliper, on the other hand, can measure length to the nearest 0.01 mm. As a result, the caliper is a more precise measurement tool because it can measure extremely minute changes in length. The measurements will be more accurate if the measuring tool is more precise.
It should be emphasized that when we represent measured values, the...
34.4K
Significant Figures in Calculations00:58

Significant Figures in Calculations

Uncertainty in measurements can be avoided by reporting the results of a calculation with the correct number of significant figures. This can be determined by the following rules for rounding numbers:
16.9K
Frictional Forces on Flat Belts01:28

Frictional Forces on Flat Belts

Flat belts are commonly used in various industrial applications for transmitting power from one pulley to another. When a flat belt is wrapped around a set of pulleys, it experiences different tensions at the driving pulley ends due to the friction between the belt and pulley surface. When the pulley moves in a counterclockwise direction, the tension T2 on the opposite side of the pulley where the belt is moving away from is higher than the tension T1 on the side where the belt is moving...
1.4K
Abrasion Resistance of Concrete01:23

Abrasion Resistance of Concrete

Abrasion resistance is an essential characteristic of concrete that determines its durability and longevity under various wear conditions. Concrete surfaces are vulnerable to different types of abrasion. For instance, surfaces may wear down due to the constant movement of vehicles or be eroded by solids carried in water, as seen in concrete canal linings. Specific tests are conducted to measure the abrasion resistance of concrete.
One such test is the revolving disc test, where three plates...
538
Stresses in a Shaft01:18

Stresses in a Shaft

The shaft PQ is subjected to a twisting force when equal and opposite torques are applied on either side. A section that cuts perpendicular to the shaft's axis at any arbitrary point R is examined to understand this. When the free-body diagram of the QR segment is analyzed, it reveals the shearing forces exerted by the PR portion onto the QR segment as the shaft experiences twisting.
Applying equilibrium conditions to the QR segment establishes that the internal shearing forces within the...
853