Related Experiment Video

Updated: Jan 23, 2026

Scale-up Chemical Synthesis of Thermally-activated Delayed Fluorescence Emitters Based on the Dibenzothiophene-S,S-Dioxide Core
08:51

Scale-up Chemical Synthesis of Thermally-activated Delayed Fluorescence Emitters Based on the Dibenzothiophene-S,S-Dioxide Core

Published on: October 24, 2017

10.1K

Tri-Spiral Donor for High Efficiency and Versatile Blue Thermally Activated Delayed Fluorescence Materials

Wei Li1, Binbin Li1, Xinyi Cai1

  • 1State Key Laboratory of Luminescent Materials and Devices and Institute of Polymer Optoelectronic Materials and Devices, South China University of Technology, Wushan Road 381, Tianhe District, Guangzhou, 510640, Guangdong Province, P. R. China.

Angewandte Chemie (International Ed. in English)
|June 14, 2019
PubMed

Keywords:
aggregationfluorescencematerials scienceorganic electronicsorganic light-emitting diodes

More Related Videos

Facile and Efficient Preparation of Tri-component Fluorescent Glycopolymers via RAFT-controlled Polymerization10:54

Facile and Efficient Preparation of Tri-component Fluorescent Glycopolymers via RAFT-controlled Polymerization

Published on: June 19, 2015

10.2K
Characterization of Thermal Transport in One-dimensional Solid Materials05:20

Characterization of Thermal Transport in One-dimensional Solid Materials

Published on: January 26, 2014

19.5K

Related Concept Videos

Cycloaddition Reactions: MO Requirements for Thermal Activation01:16

Cycloaddition Reactions: MO Requirements for Thermal Activation

Thermal cycloadditions are reactions where the source of activation energy needed to initiate the reaction is provided in the form of heat. A typical example of a thermally-allowed cycloaddition is the Diels–Alder reaction, which is a [4 + 2] cycloaddition. In contrast, a [2 + 2] cycloaddition is thermally forbidden.
4.3K
Thermal expansion and Thermal stress: Problem Solving01:27

Thermal expansion and Thermal stress: Problem Solving

San Francisco's Golden Gate Bridge is exposed to temperatures ranging from -15 °C to 40 °C. At its coldest, the main span of the bridge is 1275 m long. Assuming that the bridge is made entirely of steel, what is the change in its length between these temperatures?
To solve the problem, first, identify the known and unknown quantities. The initial length (L) of the bridge is 1275 m, the coefficient of linear expansion (α) for steel is 12 x 10-6/°C, and the change in temperature (ΔT) is 55...
2.1K
Thermal Strain01:19

Thermal Strain

Thermal strain is a concept that arises when we consider how temperature changes affect structures. Unlike the conventional assumption that structures remain constant under load, real-world scenarios often involve temperature fluctuations that can significantly impact these structures. Consider a homogeneous rod with a uniform cross-section resting freely on a flat horizontal surface. If the rod's temperature increases, the rod elongates. This elongation is proportional to the temperature...
2.8K
Thermal Expansion01:22

Thermal Expansion

The expansion of alcohol in a thermometer is one of many commonly encountered examples of thermal expansion, which is the change in size or volume of a given system as its temperature changes. The most visible example is the expansion of hot air. When air is heated, it expands and becomes less dense than the surrounding air, which then exerts an upward force on the hot air to, for example, make steam and smoke rise, and hot air balloons float. The same behavior happens in all liquids and gases,...
5.6K
Thermal Stress01:09

Thermal Stress

If the temperature of an object is changed while it is prevented from expanding or contracting, the object is subjected to stress. The stress is compressive if the object expands in the absence of constraint and tensile if it contracts. This stress resulting from temperature change is known as thermal stress. It can be quite large and can cause damage. To avoid this stress, engineers may design components so they can expand and contract freely. For instance, on highways, gaps are deliberately...
3.3K
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
384